board hal file sanitizations
This commit is contained in:
parent
7244596ded
commit
efd8f989a9
@ -25,15 +25,11 @@
|
||||
#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M
|
||||
#define GPS_INT GPIO_NUM_34 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO34
|
||||
|
||||
// Settings for on board DS3231 RTC chip
|
||||
//#define HAS_RTC MY_OLED_SDA, MY_OLED_SCL // SDA, SCL
|
||||
//#define RTC_INT GPIO_NUM_13 // timepulse with accuracy +/- 2*e-6 [microseconds] = 0,1728sec / day
|
||||
|
||||
// enable only if device has these sensors, otherwise comment these lines
|
||||
// BME680 sensor on I2C bus
|
||||
#define HAS_BME 1 // Enable BME sensors in general
|
||||
#define HAS_BME680 SDA, SCL
|
||||
#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
|
||||
//#define HAS_BME 1 // Enable BME sensors in general
|
||||
//#define HAS_BME680 SDA, SCL
|
||||
//#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
|
||||
|
||||
// display (if connected)
|
||||
#define HAS_DISPLAY U8X8_SSD1306_128X64_NONAME_HW_I2C
|
||||
@ -42,12 +38,6 @@
|
||||
#define MY_OLED_RST U8X8_PIN_NONE
|
||||
//#define DISPLAY_FLIP 1 // use if display is rotated
|
||||
|
||||
// Settings for DCF77 interface
|
||||
#define HAS_DCF77 GPIO_NUM_13
|
||||
|
||||
// Settings for IF482 interface
|
||||
//#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters
|
||||
|
||||
// user defined sensors (if connected)
|
||||
//#define HAS_SENSORS 1 // comment out if device has user defined sensors
|
||||
|
||||
|
@ -25,17 +25,12 @@
|
||||
#define RTC_INT GPIO_NUM_34 // timepulse with accuracy +/- 2*e-6 [microseconds] = 0,1728sec / day
|
||||
|
||||
// Settings for IF482 interface
|
||||
#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters
|
||||
//#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters
|
||||
|
||||
// Settings for DCF77 interface
|
||||
//#define HAS_DCF77 GPIO_NUM_14
|
||||
//#define DCF77_ACTIVE_LOW 1
|
||||
|
||||
// Settings for external GPS chip
|
||||
#define HAS_GPS 1 // use on board GPS
|
||||
#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_17, GPIO_NUM_16 // UBlox NEO 6M or 7M with default configuration
|
||||
#define GPS_INT GPIO_NUM_13
|
||||
|
||||
// Pins for LORA chip SPI interface, reset line and interrupt lines
|
||||
#define LORA_SCK (5)
|
||||
#define LORA_CS (18)
|
||||
|
Loading…
Reference in New Issue
Block a user