Merge branch 'development' of https://github.com/cyberman54/ESP32-Paxcounter into development

platformio.ini

@@ -7,7 +7,7 @@
 
 ; ---> SELECT THE TARGET PLATFORM HERE! <---
 [board]
-halfile = generic.h
+;halfile = generic.h
 ;halfile = ebox.h
 ;halfile = eboxtube.h
 ;halfile = ecopower.h
@@ -18,7 +18,7 @@ halfile = generic.h
 ;halfile = ttgov21old.h
 ;halfile = ttgov21new.h
 ;halfile = ttgofox.h
-;halfile = ttgobeam.h
+halfile = ttgobeam.h
 ;halfile = fipy.h
 ;halfile = lopy.h
 ;halfile = lopy4.h
@@ -40,7 +40,7 @@ description = Paxcounter is a device for metering passenger flows in realtime. I
 
 [common]
 ; for release_version use max. 10 chars total, use any decimal format like "a.b.c"
-release_version = 1.7.82
+release_version = 1.7.841
 ; DEBUG LEVEL: For production run set to 0, otherwise device will leak RAM while running!
 ; 0=None, 1=Error, 2=Warn, 3=Info, 4=Debug, 5=Verbose
 debug_level = 3
@@ -81,7 +81,7 @@ lib_deps_all =
 build_flags_basic =
     -include "src/hal/${board.halfile}"
     -include "src/paxcounter.conf"
-    -w
+    ;-w
     '-DCORE_DEBUG_LEVEL=${common.debug_level}'
     '-DLOG_LOCAL_LEVEL=${common.debug_level}'
     '-DPROGVERSION="${common.release_version}"'

src/hal/ttgobeam.h

@@ -29,9 +29,9 @@
 
 // enable only if device has these sensors, otherwise comment these lines
 // BME680 sensor on I2C bus
-//#define HAS_BME 1 // Enable BME sensors in general
-//#define HAS_BME680 SDA, SCL
-//#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
+#define HAS_BME 1 // Enable BME sensors in general
+#define HAS_BME680 SDA, SCL
+#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
 
 // display (if connected)
 #define HAS_DISPLAY U8X8_SSD1306_128X64_NONAME_HW_I2C

src/paxcounter.conf

@@ -71,7 +71,7 @@
 #define TIME_SYNC_INTERVAL_RETRY        10      // retry time sync after lost sync each .. minutes [default = 10], 0 means off
 #define TIME_SYNC_COMPILEDATE           0       // set to 1 to use compile date to initialize RTC after power outage [default = 0]
 #define TIME_SYNC_LORAWAN               0       // set to 1 to use LORA network as time source, 0 means off [default = 0]
-#define TIME_SYNC_LORASERVER            0       // set to 1 to use LORA timeserver as time source, 0 means off [default = 0]
+#define TIME_SYNC_LORASERVER            1       // set to 1 to use LORA timeserver as time source, 0 means off [default = 0]
 
 // settings for syncing time with timeserver applications
 #define TIME_SYNC_SAMPLES               1       // number of time requests for averaging