434 lines
14 KiB
C++
434 lines
14 KiB
C++
/*
|
|
|
|
//////////////////////// ESP32-Paxcounter \\\\\\\\\\\\\\\\\\\\\\\\\\
|
|
|
|
Copyright 2018 Oliver Brandmueller <ob@sysadm.in>
|
|
Copyright 2018 Klaus Wilting <verkehrsrot@arcor.de>
|
|
|
|
Licensed under the Apache License, Version 2.0 (the "License");
|
|
you may not use this file except in compliance with the License.
|
|
You may obtain a copy of the License at
|
|
|
|
http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
Unless required by applicable law or agreed to in writing, software
|
|
distributed under the License is distributed on an "AS IS" BASIS,
|
|
WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
See the License for the specific language governing permissions and
|
|
limitations under the License.
|
|
|
|
NOTICE:
|
|
Parts of the source files in this repository are made available under different
|
|
licenses. Refer to LICENSE.txt file in repository for more details.
|
|
|
|
//////////////////////// ESP32-Paxcounter \\\\\\\\\\\\\\\\\\\\\\\\\\
|
|
|
|
Uused tasks and timers:
|
|
|
|
Task Core Prio Purpose
|
|
====================================================================================
|
|
wifiloop 0 4 rotates wifi channels
|
|
ledloop 0 3 blinks LEDs
|
|
if482loop 1 3 serial feed of IF482 time telegrams
|
|
spiloop 0 2 reads/writes data on spi interface
|
|
IDLE 0 0 ESP32 arduino scheduler -> runs wifi sniffer
|
|
|
|
looptask 1 1 arduino core -> runs the LMIC LoRa stack
|
|
irqhandler 1 1 executes tasks triggered by irq
|
|
gpsloop 1 2 reads data from GPS via serial or i2c
|
|
bmeloop 1 1 reads data from BME sensor via i2c
|
|
IDLE 1 0 ESP32 arduino scheduler
|
|
|
|
Low priority numbers denote low priority tasks.
|
|
|
|
Tasks using i2c bus all must have same priority, because using mutex semaphore
|
|
(irqhandler, bmeloop)
|
|
|
|
ESP32 hardware timers
|
|
================================
|
|
0 triggers display refresh
|
|
1 triggers Wifi channel switch
|
|
2 triggers send payload cycle
|
|
3 triggers housekeeping cycle
|
|
|
|
RTC hardware timer (if present)
|
|
================================
|
|
triggers IF482 clock generator
|
|
|
|
*/
|
|
|
|
// Basic Config
|
|
#include "main.h"
|
|
|
|
configData_t cfg; // struct holds current device configuration
|
|
char display_line6[16], display_line7[16]; // display buffers
|
|
uint8_t volatile channel = 0; // channel rotation counter
|
|
uint16_t volatile macs_total = 0, macs_wifi = 0, macs_ble = 0,
|
|
batt_voltage = 0; // globals for display
|
|
hw_timer_t *channelSwitch = NULL, *sendCycle = NULL, *homeCycle = NULL,
|
|
*displaytimer = NULL; // irq tasks
|
|
TaskHandle_t irqHandlerTask, wifiSwitchTask;
|
|
SemaphoreHandle_t I2Caccess;
|
|
|
|
// container holding unique MAC address hashes with Memory Alloctor using PSRAM,
|
|
// if present
|
|
std::set<uint16_t, std::less<uint16_t>, Mallocator<uint16_t>> macs;
|
|
|
|
// initialize payload encoder
|
|
PayloadConvert payload(PAYLOAD_BUFFER_SIZE);
|
|
|
|
// local Tag for logging
|
|
static const char TAG[] = "main";
|
|
|
|
void setup() {
|
|
|
|
// disable the default wifi logging
|
|
esp_log_level_set("wifi", ESP_LOG_NONE);
|
|
|
|
char features[100] = "";
|
|
|
|
if (I2Caccess == NULL) // Check that semaphore has not already been created
|
|
{
|
|
I2Caccess = xSemaphoreCreateMutex(); // Create a mutex semaphore we will use
|
|
// to manage the i2c bus
|
|
if ((I2Caccess) != NULL)
|
|
xSemaphoreGive((I2Caccess)); // Flag the i2c bus available for use
|
|
}
|
|
|
|
// disable brownout detection
|
|
#ifdef DISABLE_BROWNOUT
|
|
// register with brownout is at address DR_REG_RTCCNTL_BASE + 0xd4
|
|
(*((uint32_t volatile *)ETS_UNCACHED_ADDR((DR_REG_RTCCNTL_BASE + 0xd4)))) = 0;
|
|
#endif
|
|
|
|
// setup debug output or silence device
|
|
#ifdef VERBOSE
|
|
Serial.begin(115200);
|
|
esp_log_level_set("*", ESP_LOG_VERBOSE);
|
|
#else
|
|
// mute logs completely by redirecting them to silence function
|
|
esp_log_level_set("*", ESP_LOG_NONE);
|
|
esp_log_set_vprintf(redirect_log);
|
|
#endif
|
|
|
|
ESP_LOGI(TAG, "Starting %s v%s", PRODUCTNAME, PROGVERSION);
|
|
|
|
// print chip information on startup if in verbose mode
|
|
#ifdef VERBOSE
|
|
esp_chip_info_t chip_info;
|
|
esp_chip_info(&chip_info);
|
|
ESP_LOGI(TAG,
|
|
"This is ESP32 chip with %d CPU cores, WiFi%s%s, silicon revision "
|
|
"%d, %dMB %s Flash",
|
|
chip_info.cores, (chip_info.features & CHIP_FEATURE_BT) ? "/BT" : "",
|
|
(chip_info.features & CHIP_FEATURE_BLE) ? "/BLE" : "",
|
|
chip_info.revision, spi_flash_get_chip_size() / (1024 * 1024),
|
|
(chip_info.features & CHIP_FEATURE_EMB_FLASH) ? "embedded"
|
|
: "external");
|
|
ESP_LOGI(TAG, "Internal Total heap %d, internal Free Heap %d",
|
|
ESP.getHeapSize(), ESP.getFreeHeap());
|
|
#ifdef BOARD_HAS_PSRAM
|
|
ESP_LOGI(TAG, "SPIRam Total heap %d, SPIRam Free Heap %d", ESP.getPsramSize(),
|
|
ESP.getFreePsram());
|
|
#endif
|
|
ESP_LOGI(TAG, "ChipRevision %d, Cpu Freq %d, SDK Version %s",
|
|
ESP.getChipRevision(), ESP.getCpuFreqMHz(), ESP.getSdkVersion());
|
|
ESP_LOGI(TAG, "Flash Size %d, Flash Speed %d", ESP.getFlashChipSize(),
|
|
ESP.getFlashChipSpeed());
|
|
ESP_LOGI(TAG, "Wifi/BT software coexist version: %s", esp_coex_version_get());
|
|
|
|
#ifdef HAS_GPS
|
|
ESP_LOGI(TAG, "TinyGPS+ v%s", TinyGPSPlus::libraryVersion());
|
|
#endif
|
|
|
|
#endif // verbose
|
|
|
|
// read (and initialize on first run) runtime settings from NVRAM
|
|
loadConfig(); // includes initialize if necessary
|
|
|
|
#ifdef BOARD_HAS_PSRAM
|
|
assert(psramFound());
|
|
ESP_LOGI(TAG, "PSRAM found and initialized");
|
|
strcat_P(features, " PSRAM");
|
|
#endif
|
|
|
|
// set low power mode to off
|
|
#ifdef HAS_LOWPOWER_SWITCH
|
|
pinMode(HAS_LED, OUTPUT);
|
|
digitalWrite(HAS_LOWPOWER_SWITCH, HIGH);
|
|
strcat_P(features, " LPWR");
|
|
#endif
|
|
|
|
// initialize leds
|
|
#if (HAS_LED != NOT_A_PIN)
|
|
pinMode(HAS_LED, OUTPUT);
|
|
strcat_P(features, " LED");
|
|
// switch on power LED if we have 2 LEDs, else use it for status
|
|
#ifdef HAS_RGB_LED
|
|
switch_LED(LED_ON);
|
|
strcat_P(features, " RGB");
|
|
rgb_set_color(COLOR_PINK);
|
|
#endif
|
|
#endif
|
|
|
|
#if (HAS_LED != NOT_A_PIN) || defined(HAS_RGB_LED)
|
|
// start led loop
|
|
ESP_LOGI(TAG, "Starting LED Controller...");
|
|
xTaskCreatePinnedToCore(ledLoop, // task function
|
|
"ledloop", // name of task
|
|
1024, // stack size of task
|
|
(void *)1, // parameter of the task
|
|
3, // priority of the task
|
|
&ledLoopTask, // task handle
|
|
0); // CPU core
|
|
#endif
|
|
|
|
// initialize RTC
|
|
#ifdef HAS_RTC
|
|
strcat_P(features, " RTC");
|
|
assert(rtc_init());
|
|
sync_rtctime();
|
|
#ifdef HAS_IF482
|
|
strcat_P(features, " IF482");
|
|
assert(if482_init());
|
|
ESP_LOGI(TAG, "Starting IF482 Generator...");
|
|
xTaskCreatePinnedToCore(if482_loop, // task function
|
|
"if482loop", // name of task
|
|
2048, // stack size of task
|
|
(void *)1, // parameter of the task
|
|
3, // priority of the task
|
|
&IF482Task, // task handle
|
|
0); // CPU core
|
|
#endif // HAS_IF482
|
|
#endif // HAS_RTC
|
|
|
|
// initialize wifi antenna
|
|
#ifdef HAS_ANTENNA_SWITCH
|
|
strcat_P(features, " ANT");
|
|
antenna_init();
|
|
antenna_select(cfg.wifiant);
|
|
#endif
|
|
|
|
// initialize battery status
|
|
#ifdef HAS_BATTERY_PROBE
|
|
strcat_P(features, " BATT");
|
|
calibrate_voltage();
|
|
batt_voltage = read_voltage();
|
|
#endif
|
|
|
|
#ifdef USE_OTA
|
|
strcat_P(features, " OTA");
|
|
// reboot to firmware update mode if ota trigger switch is set
|
|
if (cfg.runmode == 1) {
|
|
cfg.runmode = 0;
|
|
saveConfig();
|
|
start_ota_update();
|
|
}
|
|
#endif
|
|
|
|
// start BLE scan callback if BLE function is enabled in NVRAM configuration
|
|
// or switch off bluetooth, if not compiled
|
|
#ifdef BLECOUNTER
|
|
strcat_P(features, " BLE");
|
|
if (cfg.blescan) {
|
|
ESP_LOGI(TAG, "Starting Bluetooth...");
|
|
start_BLEscan();
|
|
} else
|
|
btStop();
|
|
#else
|
|
// remove bluetooth stack to gain more free memory
|
|
ESP_ERROR_CHECK(esp_bluedroid_disable());
|
|
ESP_ERROR_CHECK(esp_bluedroid_deinit());
|
|
btStop();
|
|
ESP_ERROR_CHECK(esp_bt_controller_deinit());
|
|
ESP_ERROR_CHECK(esp_bt_mem_release(ESP_BT_MODE_BTDM));
|
|
ESP_ERROR_CHECK(esp_coex_preference_set((
|
|
esp_coex_prefer_t)ESP_COEX_PREFER_WIFI)); // configure Wifi/BT coexist lib
|
|
#endif
|
|
|
|
// initialize button
|
|
#ifdef HAS_BUTTON
|
|
strcat_P(features, " BTN_");
|
|
#ifdef BUTTON_PULLUP
|
|
strcat_P(features, "PU");
|
|
// install button interrupt (pullup mode)
|
|
pinMode(HAS_BUTTON, INPUT_PULLUP);
|
|
#else
|
|
strcat_P(features, "PD");
|
|
// install button interrupt (pulldown mode)
|
|
pinMode(HAS_BUTTON, INPUT_PULLDOWN);
|
|
#endif // BUTTON_PULLUP
|
|
#endif // HAS_BUTTON
|
|
|
|
// initialize gps
|
|
#ifdef HAS_GPS
|
|
strcat_P(features, " GPS");
|
|
if (gps_init()) {
|
|
ESP_LOGI(TAG, "Starting GPS Feed...");
|
|
xTaskCreatePinnedToCore(gps_loop, // task function
|
|
"gpsloop", // name of task
|
|
2048, // stack size of task
|
|
(void *)1, // parameter of the task
|
|
2, // priority of the task
|
|
&GpsTask, // task handle
|
|
1); // CPU core
|
|
}
|
|
#endif
|
|
|
|
// initialize sensors
|
|
#ifdef HAS_SENSORS
|
|
strcat_P(features, " SENS");
|
|
sensor_init();
|
|
#endif
|
|
|
|
// initialize LoRa
|
|
#ifdef HAS_LORA
|
|
strcat_P(features, " LORA");
|
|
#endif
|
|
assert(lora_stack_init() == ESP_OK);
|
|
|
|
// initialize SPI
|
|
#ifdef HAS_SPI
|
|
strcat_P(features, " SPI");
|
|
#endif
|
|
assert(spi_init() == ESP_OK);
|
|
|
|
#ifdef VENDORFILTER
|
|
strcat_P(features, " OUIFLT");
|
|
#endif
|
|
|
|
// initialize display
|
|
#ifdef HAS_DISPLAY
|
|
strcat_P(features, " OLED");
|
|
DisplayState = cfg.screenon;
|
|
init_display(PRODUCTNAME, PROGVERSION);
|
|
|
|
// setup display refresh trigger IRQ using esp32 hardware timer
|
|
// https://techtutorialsx.com/2017/10/07/esp32-arduino-timer-interrupts/
|
|
// prescaler 80 -> divides 80 MHz CPU freq to 1 MHz, timer 0, count up
|
|
displaytimer = timerBegin(0, 80, true);
|
|
// interrupt handler DisplayIRQ, triggered by edge
|
|
timerAttachInterrupt(displaytimer, &DisplayIRQ, true);
|
|
// reload interrupt after each trigger of display refresh cycle
|
|
timerAlarmWrite(displaytimer, DISPLAYREFRESH_MS * 1000, true);
|
|
#endif
|
|
|
|
// setup send cycle trigger IRQ using esp32 hardware timer 2
|
|
sendCycle = timerBegin(2, 8000, true);
|
|
timerAttachInterrupt(sendCycle, &SendCycleIRQ, true);
|
|
timerAlarmWrite(sendCycle, cfg.sendcycle * 2 * 10000, true);
|
|
|
|
// setup house keeping cycle trigger IRQ using esp32 hardware timer 3
|
|
homeCycle = timerBegin(3, 8000, true);
|
|
timerAttachInterrupt(homeCycle, &homeCycleIRQ, true);
|
|
timerAlarmWrite(homeCycle, HOMECYCLE * 10000, true);
|
|
|
|
// setup channel rotation trigger IRQ using esp32 hardware timer 1
|
|
channelSwitch = timerBegin(1, 800, true);
|
|
timerAttachInterrupt(channelSwitch, &ChannelSwitchIRQ, true);
|
|
timerAlarmWrite(channelSwitch, cfg.wifichancycle * 1000, true);
|
|
|
|
// show payload encoder
|
|
#if PAYLOAD_ENCODER == 1
|
|
strcat_P(features, " PLAIN");
|
|
#elif PAYLOAD_ENCODER == 2
|
|
strcat_P(features, " PACKED");
|
|
#elif PAYLOAD_ENCODER == 3
|
|
strcat_P(features, " LPPDYN");
|
|
#elif PAYLOAD_ENCODER == 4
|
|
strcat_P(features, " LPPPKD");
|
|
#endif
|
|
|
|
// show compiled features
|
|
ESP_LOGI(TAG, "Features:%s", features);
|
|
|
|
#ifdef HAS_LORA
|
|
// output LoRaWAN keys to console
|
|
#ifdef VERBOSE
|
|
showLoraKeys();
|
|
#endif
|
|
#endif
|
|
|
|
// start wifi in monitor mode and start channel rotation task on core 0
|
|
ESP_LOGI(TAG, "Starting Wifi...");
|
|
wifi_sniffer_init();
|
|
// initialize salt value using esp_random() called by random() in
|
|
// arduino-esp32 core. Note: do this *after* wifi has started, since
|
|
// function gets it's seed from RF noise
|
|
get_salt(); // get new 16bit for salting hashes
|
|
|
|
// start state machine
|
|
ESP_LOGI(TAG, "Starting Interrupt Handler...");
|
|
xTaskCreatePinnedToCore(irqHandler, // task function
|
|
"irqhandler", // name of task
|
|
4096, // stack size of task
|
|
(void *)1, // parameter of the task
|
|
1, // priority of the task
|
|
&irqHandlerTask, // task handle
|
|
1); // CPU core
|
|
|
|
// start wifi channel rotation task
|
|
ESP_LOGI(TAG, "Starting Wifi Channel rotation...");
|
|
xTaskCreatePinnedToCore(switchWifiChannel, // task function
|
|
"wifiloop", // name of task
|
|
2048, // stack size of task
|
|
NULL, // parameter of the task
|
|
4, // priority of the task
|
|
&wifiSwitchTask, // task handle
|
|
0); // CPU core
|
|
|
|
// initialize bme
|
|
#ifdef HAS_BME
|
|
strcat_P(features, " BME");
|
|
if (bme_init()) {
|
|
ESP_LOGI(TAG, "Starting Bluetooth sniffer...");
|
|
xTaskCreatePinnedToCore(bme_loop, // task function
|
|
"bmeloop", // name of task
|
|
2048, // stack size of task
|
|
(void *)1, // parameter of the task
|
|
1, // priority of the task
|
|
&BmeTask, // task handle
|
|
1); // CPU core
|
|
}
|
|
#endif
|
|
|
|
assert(irqHandlerTask != NULL); // has interrupt handler task started?
|
|
// start timer triggered interrupts
|
|
ESP_LOGI(TAG, "Starting Interrupts...");
|
|
#ifdef HAS_DISPLAY
|
|
timerAlarmEnable(displaytimer);
|
|
#endif
|
|
timerAlarmEnable(sendCycle);
|
|
timerAlarmEnable(homeCycle);
|
|
timerAlarmEnable(channelSwitch);
|
|
|
|
// start button interrupt
|
|
#ifdef HAS_BUTTON
|
|
#ifdef BUTTON_PULLUP
|
|
attachInterrupt(digitalPinToInterrupt(HAS_BUTTON), ButtonIRQ, RISING);
|
|
#else
|
|
attachInterrupt(digitalPinToInterrupt(HAS_BUTTON), ButtonIRQ, FALLING);
|
|
#endif
|
|
#endif // HAS_BUTTON
|
|
|
|
// start RTC interrupt
|
|
#if defined HAS_IF482 && defined HAS_RTC
|
|
// setup external interupt for active low RTC INT pin
|
|
assert(IF482Task != NULL); // has if482loop task started?
|
|
ESP_LOGI(TAG, "Starting IF482 output...");
|
|
attachInterrupt(digitalPinToInterrupt(RTC_INT), IF482IRQ, FALLING);
|
|
#endif
|
|
|
|
} // setup()
|
|
|
|
void loop() {
|
|
|
|
while (1) {
|
|
#ifdef HAS_LORA
|
|
os_runloop_once(); // execute lmic scheduled jobs and events
|
|
#endif
|
|
delay(2); // yield to CPU
|
|
}
|
|
|
|
vTaskDelete(NULL); // shoud never be reached
|
|
} |