88 lines
3.3 KiB
C
88 lines
3.3 KiB
C
// clang-format off
|
|
// upload_speed 921600
|
|
// board m5stack-fire
|
|
|
|
// note use of GPIO16/17
|
|
// https://www.bjoerns-techblog.de/2019/03/m5stack-fire-eine-uebersicht/
|
|
|
|
#ifndef _M5FIRE_H
|
|
#define _M5FIRE_H
|
|
|
|
#include <stdint.h>
|
|
|
|
#define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no M5 RA01 LoRa module
|
|
#define LORA_SCK SCK
|
|
#define LORA_CS SS
|
|
#define LORA_MISO MISO
|
|
#define LORA_MOSI MOSI
|
|
#define LORA_RST GPIO_NUM_26
|
|
#define LORA_IRQ GPIO_NUM_36
|
|
#define LORA_IO1 GPIO_NUM_34 // must be wired by you on PCB!
|
|
#define LORA_IO2 LMIC_UNUSED_PIN
|
|
|
|
|
|
// enable only if you want to store a local paxcount table on the device
|
|
#define HAS_SDCARD 1 // this board has an SD-card-reader/writer
|
|
#define SDCARD_CS GPIO_NUM_4
|
|
#define SDCARD_MOSI MOSI
|
|
#define SDCARD_MISO MISO
|
|
#define SDCARD_SCLK SCK
|
|
|
|
#define CFG_sx1276_radio 1 // select LoRa chip
|
|
#define BOARD_HAS_PSRAM // use if board has external PSRAM
|
|
#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
|
|
|
|
#define HAS_DISPLAY 2 // TFT-LCD, support work in progess, not ready yet
|
|
//#define MY_DISPLAY_FLIP 1 // use if display is rotated
|
|
|
|
#define HAS_LED NOT_A_PIN // no on board LED (?)
|
|
#define RGB_LED_COUNT 10
|
|
|
|
#define HAS_RGB_LED SmartLed rgb_led(LED_SK6812, RGB_LED_COUNT, GPIO_NUM_15) // LED_SK6812 RGB LED on GPIO15
|
|
#define HAS_BUTTON (39) // on board button A
|
|
|
|
// power management settings
|
|
#define HAS_IP5306 1 // has IP5306 chip
|
|
#define PMU_CHG_CURRENT 2 // battery charge current
|
|
// possible values: 0:200mA, 1:400mA, *2:500mA, 3:600mA
|
|
#define PMU_CHG_CUTOFF 0 // battery charge cutoff
|
|
// possible values: *0:4.2V, 1:4.3V, 2:4.35V, 3:4.4V
|
|
|
|
// GPS settings
|
|
#define HAS_GPS 0 // use on board GPS
|
|
#define GPS_SERIAL 9600, SERIAL_8N1, RXD2, TXD2 // UBlox NEO 6M RX, TX
|
|
// #define GPS_INT GPIO_NUM_35 // 30ns accurary timepulse, to be external wired on pcb: shorten R12!
|
|
|
|
// Display Settings
|
|
#define MY_DISPLAY_WIDTH 320
|
|
#define MY_DISPLAY_HEIGHT 240
|
|
#define MY_DISPLAY_INVERT 1
|
|
|
|
// setting for M5 display
|
|
#define USER_SETUP_LOADED 1
|
|
#define ILI9341_DRIVER 1
|
|
#define M5STACK // needed for TFT driver
|
|
|
|
#define TFT_MISO MISO // SPI
|
|
#define TFT_MOSI MOSI // SPI
|
|
#define TFT_SCLK SCK // SPI
|
|
#define TFT_CS GPIO_NUM_14 // Chip select control
|
|
#define TFT_DC GPIO_NUM_27 // Data Command control
|
|
#define TFT_RST GPIO_NUM_33 // Reset
|
|
#define TFT_BL GPIO_NUM_32 // LED back-light
|
|
|
|
#define TFT_RGB_ORDER TFT_BGR // Colour order Blue-Green-Red
|
|
|
|
//#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
|
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
|
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
|
//#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
|
//#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
|
|
//#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
|
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
|
|
//#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
|
#define SMOOTH_FONT
|
|
|
|
#define SPI_FREQUENCY 40000000
|
|
|
|
#endif |