109 lines
3.8 KiB
C
109 lines
3.8 KiB
C
// clang-format off
|
|
// upload_speed 115200
|
|
// board esp32dev
|
|
// display_library lib_deps_oled_display
|
|
|
|
#ifndef _GENERIC_H
|
|
#define _GENERIC_H
|
|
|
|
#include <stdint.h>
|
|
|
|
// Hardware related definitions for generic ESP32 boards
|
|
// generic.h is kitchensink with all available options
|
|
|
|
#define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no LoRa
|
|
#define HAS_SPI 1 // comment out if device shall not send data via SPI
|
|
// pin definitions for SPI slave interface
|
|
#define SPI_MOSI GPIO_NUM_23
|
|
#define SPI_MISO GPIO_NUM_19
|
|
#define SPI_SCLK GPIO_NUM_18
|
|
#define SPI_CS GPIO_NUM_5
|
|
|
|
// enable only if you want to store a local paxcount table on the device
|
|
#define HAS_SDCARD 1 // this board has an SD-card-reader/writer
|
|
// Pins for SD-card
|
|
#define SDCARD_CS (13)
|
|
#define SDCARD_MOSI (15)
|
|
#define SDCARD_MISO (2)
|
|
#define SDCARD_SCLK (14)
|
|
|
|
// enable only if device has these sensors, otherwise comment these lines
|
|
// tutorial to connect BME sensor see here:
|
|
// https://sbamueller.wordpress.com/2019/02/26/paxcounter-mit-umweltsensor/
|
|
//
|
|
// in platformio.ini append
|
|
// lib_deps = <...> ${common.lib_deps_sensors}
|
|
// for loading necessary libraries
|
|
|
|
// BME680 sensor on I2C bus
|
|
#define HAS_BME 1 // Enable BME sensors in general
|
|
#define HAS_BME680 GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
|
|
#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // connect SDIO of BME680 to GND
|
|
|
|
// BME280 sensor on I2C bus
|
|
//#define HAS_BME 1 // Enable BME sensors in general
|
|
//#define HAS_BME280 GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
|
|
//#define BME280_ADDR 0x76 // change to 0x77 depending on your wiring
|
|
|
|
// BMP180 sensor on I2C bus
|
|
//#define HAS_BMP180
|
|
//#define BMP180_ADDR 0x77
|
|
|
|
// SDS011 dust sensor settings
|
|
#define HAS_SDS011 1 // use SDS011
|
|
// used pins on the ESP-side:
|
|
#define SDS_TX 19 // connect to RX on the SDS011
|
|
#define SDS_RX 23 // connect to TX on the SDS011
|
|
|
|
// up to three user defined sensors (if connected)
|
|
//#define HAS_SENSOR_1 1 // comment out if device has user defined sensor #1
|
|
//#define HAS_SENSOR_2 1 // comment out if device has user defined sensor #2
|
|
//#define HAS_SENSOR_3 1 // comment out if device has user defined sensor #3
|
|
|
|
#define CFG_sx1276_radio 1 // select LoRa chip
|
|
//#define CFG_sx1272_radio 1 // select LoRa chip
|
|
#define BOARD_HAS_PSRAM // use if board has external PSRAM
|
|
#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
|
|
|
|
#define HAS_DISPLAY 1
|
|
//#define MY_DISPLAY_FLIP 1 // use if display is rotated
|
|
#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
|
|
#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
|
|
|
|
#define HAS_LED (21) // on board LED
|
|
#define HAS_BUTTON (39) // on board button
|
|
#define HAS_RGB_LED SmartLed rgb_led(LED_WS2812, 1, GPIO_NUM_0) // WS2812B RGB LED on GPIO0
|
|
|
|
// GPS settings
|
|
#define HAS_GPS 1 // use on board GPS
|
|
#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M RX, TX
|
|
#define GPS_INT GPIO_NUM_13 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO13
|
|
|
|
// Pins for I2C interface of OLED Display
|
|
#define MY_DISPLAY_SDA (4)
|
|
#define MY_DISPLAY_SCL (15)
|
|
#define MY_DISPLAY_RST (16)
|
|
|
|
// Settings for on board DS3231 RTC chip
|
|
#define HAS_RTC MY_DISPLAY_SDA, MY_DISPLAY_SCL // SDA, SCL
|
|
#define RTC_INT GPIO_NUM_34 // timepulse with accuracy +/- 2*e-6 [microseconds] = 0,1728sec / day
|
|
|
|
// Settings for IF482 interface
|
|
//#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters
|
|
|
|
// Settings for DCF77 interface
|
|
//#define HAS_DCF77 GPIO_NUM_1
|
|
//#define DCF77_ACTIVE_LOW 1
|
|
|
|
// Pins for LORA chip SPI interface, reset line and interrupt lines
|
|
#define LORA_SCK (5)
|
|
#define LORA_CS (18)
|
|
#define LORA_MISO (19)
|
|
#define LORA_MOSI (27)
|
|
#define LORA_RST (14)
|
|
#define LORA_IRQ (26)
|
|
#define LORA_IO1 (33)
|
|
#define LORA_IO2 LMIC_UNUSED_PIN
|
|
|
|
#endif
|