100 lines
4.1 KiB
C
100 lines
4.1 KiB
C
// COUNTRY AND PROJECT SPECIFIC DEFINITIONS FOR LMIC STACK
|
|
|
|
// COUNTRY SETTINGS
|
|
// --> please check with you local regulations for ISM band frequency use!
|
|
|
|
#define CFG_eu868 1 // Europe (high band)
|
|
//#define CFG_eu433 1 // Europe (low band)
|
|
//#define CFG_us915 1 // USA, Canada and South America
|
|
//#define CFG_in866 1 // India
|
|
//#define CFG_au921 1 // Australia
|
|
//#define CFG_as923 1 // Asia
|
|
//#define CFG_cn783 1 // China (high band)
|
|
//#define CFG_cn490 1 // China (low band)
|
|
//#define CFG_kr920 1 // Korea
|
|
|
|
// LMIC LORAWAN STACK SETTINGS
|
|
// --> adapt to your device only if necessary
|
|
|
|
// use interrupts only if LORA_IRQ and LORA_DIO are connected to interrupt
|
|
// capable GPIO pins on your board, if not disable interrupts
|
|
#define LMIC_USE_INTERRUPTS 1
|
|
|
|
// time sync via LoRaWAN network, note: not supported by TTNv2
|
|
// #define LMIC_ENABLE_DeviceTimeReq 1
|
|
|
|
// This tells LMIC to make the receive windows bigger, in case your clock is
|
|
// faster or slower. This causes the transceiver to be earlier switched on,
|
|
// so consuming more power. You may sharpen (reduce) this value if you are
|
|
// limited on battery.
|
|
// ATTN: VALUES > 7 WILL CAUSE RECEPTION AND JOIN PROBLEMS WITH HIGH SF RATES
|
|
//#define CLOCK_ERROR_PROCENTAGE 7
|
|
|
|
// Set this to 1 to enable some basic debug output (using printf) about
|
|
// RF settings used during transmission and reception. Set to 2 to
|
|
// enable more verbose output. Make sure that printf is actually
|
|
// configured (e.g. on AVR it is not by default), otherwise using it can
|
|
// cause crashing.
|
|
#define LMIC_DEBUG_LEVEL 0
|
|
|
|
// Enable this to allow using printf() to print to the given serial port
|
|
// (or any other Print object). This can be easy for debugging. The
|
|
// current implementation only works on AVR, though.
|
|
//#define LMIC_PRINTF_TO Serial
|
|
|
|
// Change the SPI clock speed if you encounter errors
|
|
// communicating with the radio.
|
|
// The standard range is 125kHz-8MHz, but some boards can go faster.
|
|
//#define LMIC_SPI_FREQ 1E6
|
|
|
|
// Any runtime assertion failures are printed to this serial port (or
|
|
// any other Print object). If this is unset, any failures just silently
|
|
// halt execution.
|
|
#define LMIC_FAILURE_TO Serial
|
|
|
|
// Uncomment this to disable all code related to joining
|
|
//#define DISABLE_JOIN
|
|
// Uncomment this to disable all code related to ping
|
|
#define DISABLE_PING
|
|
// Uncomment this to disable all code related to beacon tracking.
|
|
// Requires ping to be disabled too
|
|
#define DISABLE_BEACONS
|
|
|
|
// Uncomment these to disable the corresponding MAC commands.
|
|
// Class A
|
|
//#define DISABLE_MCMD_DCAP_REQ // duty cycle cap
|
|
//#define DISABLE_MCMD_DN2P_SET // 2nd DN window param
|
|
//#define DISABLE_MCMD_SNCH_REQ // set new channel
|
|
// Class B
|
|
//#define DISABLE_MCMD_PING_SET // set ping freq, automatically disabled by
|
|
// DISABLE_PING #define DISABLE_MCMD_BCNI_ANS // next beacon start, automatical
|
|
// disabled by DISABLE_BEACON
|
|
|
|
// In LoRaWAN, a gateway applies I/Q inversion on TX, and nodes do the
|
|
// same on RX. This ensures that gateways can talk to nodes and vice
|
|
// versa, but gateways will not hear other gateways and nodes will not
|
|
// hear other nodes. By uncommenting this macro, this inversion is
|
|
// disabled and this node can hear other nodes. If two nodes both have
|
|
// this macro set, they can talk to each other (but they can no longer
|
|
// hear gateways). This should probably only be used when debugging
|
|
// and/or when talking to the radio directly (e.g. like in the "raw"
|
|
// example).
|
|
//#define DISABLE_INVERT_IQ_ON_RX
|
|
|
|
// This allows choosing between multiple included AES implementations.
|
|
// Make sure exactly one of these is uncommented.
|
|
//
|
|
// This selects the original AES implementation included LMIC. This
|
|
// implementation is optimized for speed on 32-bit processors using
|
|
// fairly big lookup tables, but it takes up big amounts of flash on the
|
|
// AVR architecture.
|
|
#define USE_ORIGINAL_AES
|
|
//
|
|
// This selects the AES implementation written by Ideetroon for their
|
|
// own LoRaWAN library. It also uses lookup tables, but smaller
|
|
// byte-oriented ones, making it use a lot less flash space (but it is
|
|
// also about twice as slow as the original).
|
|
// #define USE_IDEETRON_AES
|
|
//
|
|
//#define USE_MBEDTLS_AES
|