227 lines
8.9 KiB
C++
227 lines
8.9 KiB
C++
/*******************************************************************************
|
|
* Copyright (c) 2015 Thomas Telkamp and Matthijs Kooijman
|
|
*
|
|
* Permission is hereby granted, free of charge, to anyone
|
|
* obtaining a copy of this document and accompanying files,
|
|
* to do whatever they want with them without any restriction,
|
|
* including, but not limited to, copying, modification and redistribution.
|
|
* NO WARRANTY OF ANY KIND IS PROVIDED.
|
|
*
|
|
* This example sends a valid LoRaWAN packet with payload "Hello,
|
|
* world!", using frequency and encryption settings matching those of
|
|
* the The Things Network.
|
|
*
|
|
* This uses ABP (Activation-by-personalisation), where a DevAddr and
|
|
* Session keys are preconfigured (unlike OTAA, where a DevEUI and
|
|
* application key is configured, while the DevAddr and session keys are
|
|
* assigned/generated in the over-the-air-activation procedure).
|
|
*
|
|
* Note: LoRaWAN per sub-band duty-cycle limitation is enforced (1% in
|
|
* g1, 0.1% in g2), but not the TTN fair usage policy (which is probably
|
|
* violated by this sketch when left running for longer)!
|
|
*
|
|
* To use this sketch, first register your application and device with
|
|
* the things network, to set or generate a DevAddr, NwkSKey and
|
|
* AppSKey. Each device should have their own unique values for these
|
|
* fields.
|
|
*
|
|
* Do not forget to define the radio type correctly in config.h.
|
|
*
|
|
*******************************************************************************/
|
|
|
|
#include <lmic.h>
|
|
#include <hal/hal.h>
|
|
#include <SPI.h>
|
|
|
|
// LoRaWAN NwkSKey, network session key
|
|
// This is the default Semtech key, which is used by the early prototype TTN
|
|
// network.
|
|
static const PROGMEM u1_t NWKSKEY[16] = { 0x2B, 0x7E, 0x15, 0x16, 0x28, 0xAE, 0xD2, 0xA6, 0xAB, 0xF7, 0x15, 0x88, 0x09, 0xCF, 0x4F, 0x3C };
|
|
|
|
// LoRaWAN AppSKey, application session key
|
|
// This is the default Semtech key, which is used by the early prototype TTN
|
|
// network.
|
|
static const u1_t PROGMEM APPSKEY[16] = { 0x2B, 0x7E, 0x15, 0x16, 0x28, 0xAE, 0xD2, 0xA6, 0xAB, 0xF7, 0x15, 0x88, 0x09, 0xCF, 0x4F, 0x3C };
|
|
|
|
// LoRaWAN end-device address (DevAddr)
|
|
static const u4_t DEVADDR = 0x03FF0001 ; // <-- Change this address for every node!
|
|
|
|
// These callbacks are only used in over-the-air activation, so they are
|
|
// left empty here (we cannot leave them out completely unless
|
|
// DISABLE_JOIN is set in config.h, otherwise the linker will complain).
|
|
void os_getArtEui (u1_t* buf) { }
|
|
void os_getDevEui (u1_t* buf) { }
|
|
void os_getDevKey (u1_t* buf) { }
|
|
|
|
static uint8_t mydata[] = "Hello, world!";
|
|
static osjob_t sendjob;
|
|
|
|
// Schedule TX every this many seconds (might become longer due to duty
|
|
// cycle limitations).
|
|
const unsigned TX_INTERVAL = 60;
|
|
|
|
// Pin mapping
|
|
const lmic_pinmap lmic_pins = {
|
|
.nss = 6,
|
|
.rxtx = LMIC_UNUSED_PIN,
|
|
.rst = 5,
|
|
.dio = {2, 3, 4},
|
|
};
|
|
|
|
void onEvent (ev_t ev) {
|
|
Serial.print(os_getTime());
|
|
Serial.print(": ");
|
|
switch(ev) {
|
|
case EV_SCAN_TIMEOUT:
|
|
Serial.println(F("EV_SCAN_TIMEOUT"));
|
|
break;
|
|
case EV_BEACON_FOUND:
|
|
Serial.println(F("EV_BEACON_FOUND"));
|
|
break;
|
|
case EV_BEACON_MISSED:
|
|
Serial.println(F("EV_BEACON_MISSED"));
|
|
break;
|
|
case EV_BEACON_TRACKED:
|
|
Serial.println(F("EV_BEACON_TRACKED"));
|
|
break;
|
|
case EV_JOINING:
|
|
Serial.println(F("EV_JOINING"));
|
|
break;
|
|
case EV_JOINED:
|
|
Serial.println(F("EV_JOINED"));
|
|
break;
|
|
case EV_RFU1:
|
|
Serial.println(F("EV_RFU1"));
|
|
break;
|
|
case EV_JOIN_FAILED:
|
|
Serial.println(F("EV_JOIN_FAILED"));
|
|
break;
|
|
case EV_REJOIN_FAILED:
|
|
Serial.println(F("EV_REJOIN_FAILED"));
|
|
break;
|
|
case EV_TXCOMPLETE:
|
|
Serial.println(F("EV_TXCOMPLETE (includes waiting for RX windows)"));
|
|
if (LMIC.txrxFlags & TXRX_ACK)
|
|
Serial.println(F("Received ack"));
|
|
if (LMIC.dataLen) {
|
|
Serial.println(F("Received "));
|
|
Serial.println(LMIC.dataLen);
|
|
Serial.println(F(" bytes of payload"));
|
|
}
|
|
// Schedule next transmission
|
|
os_setTimedCallback(&sendjob, os_getTime()+sec2osticks(TX_INTERVAL), do_send);
|
|
break;
|
|
case EV_LOST_TSYNC:
|
|
Serial.println(F("EV_LOST_TSYNC"));
|
|
break;
|
|
case EV_RESET:
|
|
Serial.println(F("EV_RESET"));
|
|
break;
|
|
case EV_RXCOMPLETE:
|
|
// data received in ping slot
|
|
Serial.println(F("EV_RXCOMPLETE"));
|
|
break;
|
|
case EV_LINK_DEAD:
|
|
Serial.println(F("EV_LINK_DEAD"));
|
|
break;
|
|
case EV_LINK_ALIVE:
|
|
Serial.println(F("EV_LINK_ALIVE"));
|
|
break;
|
|
default:
|
|
Serial.println(F("Unknown event"));
|
|
break;
|
|
}
|
|
}
|
|
|
|
void do_send(osjob_t* j){
|
|
// Check if there is not a current TX/RX job running
|
|
if (LMIC.opmode & OP_TXRXPEND) {
|
|
Serial.println(F("OP_TXRXPEND, not sending"));
|
|
} else {
|
|
// Prepare upstream data transmission at the next possible time.
|
|
LMIC_setTxData2(1, mydata, sizeof(mydata)-1, 0);
|
|
Serial.println(F("Packet queued"));
|
|
}
|
|
// Next TX is scheduled after TX_COMPLETE event.
|
|
}
|
|
|
|
void setup() {
|
|
Serial.begin(115200);
|
|
Serial.println(F("Starting"));
|
|
|
|
#ifdef VCC_ENABLE
|
|
// For Pinoccio Scout boards
|
|
pinMode(VCC_ENABLE, OUTPUT);
|
|
digitalWrite(VCC_ENABLE, HIGH);
|
|
delay(1000);
|
|
#endif
|
|
|
|
// LMIC init
|
|
os_init();
|
|
// Reset the MAC state. Session and pending data transfers will be discarded.
|
|
LMIC_reset();
|
|
|
|
// Set static session parameters. Instead of dynamically establishing a session
|
|
// by joining the network, precomputed session parameters are be provided.
|
|
#ifdef PROGMEM
|
|
// On AVR, these values are stored in flash and only copied to RAM
|
|
// once. Copy them to a temporary buffer here, LMIC_setSession will
|
|
// copy them into a buffer of its own again.
|
|
uint8_t appskey[sizeof(APPSKEY)];
|
|
uint8_t nwkskey[sizeof(NWKSKEY)];
|
|
memcpy_P(appskey, APPSKEY, sizeof(APPSKEY));
|
|
memcpy_P(nwkskey, NWKSKEY, sizeof(NWKSKEY));
|
|
LMIC_setSession (0x1, DEVADDR, nwkskey, appskey);
|
|
#else
|
|
// If not running an AVR with PROGMEM, just use the arrays directly
|
|
LMIC_setSession (0x1, DEVADDR, NWKSKEY, APPSKEY);
|
|
#endif
|
|
|
|
#if defined(CFG_eu868)
|
|
// Set up the channels used by the Things Network, which corresponds
|
|
// to the defaults of most gateways. Without this, only three base
|
|
// channels from the LoRaWAN specification are used, which certainly
|
|
// works, so it is good for debugging, but can overload those
|
|
// frequencies, so be sure to configure the full frequency range of
|
|
// your network here (unless your network autoconfigures them).
|
|
// Setting up channels should happen after LMIC_setSession, as that
|
|
// configures the minimal channel set.
|
|
// NA-US channels 0-71 are configured automatically
|
|
LMIC_setupChannel(0, 868100000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(1, 868300000, DR_RANGE_MAP(DR_SF12, DR_SF7B), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(2, 868500000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(3, 867100000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(4, 867300000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(5, 867500000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(6, 867700000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(7, 867900000, DR_RANGE_MAP(DR_SF12, DR_SF7), BAND_CENTI); // g-band
|
|
LMIC_setupChannel(8, 868800000, DR_RANGE_MAP(DR_FSK, DR_FSK), BAND_MILLI); // g2-band
|
|
// TTN defines an additional channel at 869.525Mhz using SF9 for class B
|
|
// devices' ping slots. LMIC does not have an easy way to define set this
|
|
// frequency and support for class B is spotty and untested, so this
|
|
// frequency is not configured here.
|
|
#elif defined(CFG_us915)
|
|
// NA-US channels 0-71 are configured automatically
|
|
// but only one group of 8 should (a subband) should be active
|
|
// TTN recommends the second sub band, 1 in a zero based count.
|
|
// https://github.com/TheThingsNetwork/gateway-conf/blob/master/US-global_conf.json
|
|
LMIC_selectSubBand(1);
|
|
#endif
|
|
|
|
// Disable link check validation
|
|
LMIC_setLinkCheckMode(0);
|
|
|
|
// TTN uses SF9 for its RX2 window.
|
|
LMIC.dn2Dr = DR_SF9;
|
|
|
|
// Set data rate and transmit power for uplink (note: txpow seems to be ignored by the library)
|
|
LMIC_setDrTxpow(DR_SF7,14);
|
|
|
|
// Start job
|
|
do_send(&sendjob);
|
|
}
|
|
|
|
void loop() {
|
|
os_runloop_once();
|
|
}
|