52 lines
2.0 KiB
C
52 lines
2.0 KiB
C
// clang-format off
|
|
|
|
#ifndef _TTGOBEAM_H
|
|
#define _TTGOBEAM_H
|
|
|
|
#include <stdint.h>
|
|
|
|
// Hardware related definitions for TTGO T-Beam board
|
|
// (only) for older T-Beam version T22_V05 eternal wiring LORA_IO1 to GPIO33 is needed!
|
|
//
|
|
// pinouts taken from http://tinymicros.com/wiki/TTGO_T-Beam
|
|
|
|
#define HAS_LED GPIO_NUM_14 // on board green LED, only new version TTGO-BEAM V07
|
|
//#define HAS_LED GPIO_NUM_21 // on board green LED, only old verison TTGO-BEAM V05
|
|
|
|
#define HAS_LORA 1 // comment out if device shall not send data via LoRa
|
|
#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
|
|
#define BOARD_HAS_PSRAM // use extra 4MB external RAM
|
|
#define HAS_BUTTON GPIO_NUM_39 // on board button (next to reset)
|
|
#define HAS_BATTERY_PROBE ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
|
|
#define BATT_FACTOR 2 // voltage divider 100k/100k on board
|
|
|
|
// GPS settings
|
|
#define HAS_GPS 1 // use on board GPS
|
|
#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M
|
|
//#define GPS_INT GPIO_NUM_34 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO34
|
|
//#define GPS_CLK (1000) // pulse length 100ms, accuracy +/- 3 *e-8 [nanoseconds] = 0,95sec / year
|
|
|
|
// enable only if device has these sensors, otherwise comment these lines
|
|
// BME680 sensor on I2C bus
|
|
//#define HAS_BME SDA, SCL
|
|
//#define BME_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
|
|
|
|
// display (if connected)
|
|
//#define HAS_DISPLAY U8X8_SSD1306_128X64_NONAME_HW_I2C
|
|
//#define MY_OLED_SDA SDA
|
|
//#define MY_OLED_SCL SCL
|
|
//#define MY_OLED_RST U8X8_PIN_NONE
|
|
//#define DISPLAY_FLIP 1 // use if display is rotated
|
|
|
|
// Settings for DCF77 interface
|
|
//#define HAS_DCF77 GPIO_NUM_13
|
|
|
|
// Settings for IF482 interface
|
|
//#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters
|
|
|
|
// user defined sensors (if connected)
|
|
//#define HAS_SENSORS 1 // comment out if device has user defined sensors
|
|
|
|
//#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
|
|
|
|
#endif |