76 lines
4.8 KiB
Plaintext
76 lines
4.8 KiB
Plaintext
// ----- Paxcounter user config file ------
|
|
//
|
|
// --> adapt to your needs and use case <--
|
|
//
|
|
// Note: After editing, before "build", use "clean" button in PlatformIO!
|
|
|
|
#define PRODUCTNAME "PAXCNT"
|
|
|
|
// Verbose enables serial output
|
|
#define VERBOSE 1 // comment out to silence the device, for mute use build option
|
|
|
|
// Payload send cycle and encoding
|
|
#define SEND_SECS 30 // payload send cycle [seconds/2] -> 60 sec.
|
|
#define PAYLOAD_ENCODER 2 // payload encoder: 1=Plain, 2=Packed, 3=CayenneLPP dynamic, 4=CayenneLPP packed
|
|
|
|
// Set this to include BLE counting and vendor filter functions
|
|
#define VENDORFILTER 1 // comment out if you want to count things, not people
|
|
#define BLECOUNTER 1 // comment out if you don't want BLE count, saves power & memory
|
|
|
|
// BLE scan parameters
|
|
#define BLESCANTIME 0 // [seconds] scan duration, 0 means infinite [default], see note below
|
|
#define BLESCANWINDOW 80 // [milliseconds] scan window, see below, 3 .. 10240, default 80ms
|
|
#define BLESCANINTERVAL 80 // [illiseconds] scan interval, see below, 3 .. 10240, default 80ms = 100% duty cycle
|
|
|
|
/* Note: guide for setting bluetooth parameters
|
|
*
|
|
* |< Scan Window > |< Scan Window > | ... |< Scan Window > |
|
|
* |< Scan Interval >|< Scan Interval >| ... |< Scan Interval >|
|
|
* |< Scan duration >|
|
|
*
|
|
* Scan duration sets how long scanning should be going on, before starting a new scan cycle. 0 means infinite (default).
|
|
* Scan window sets how much of the interval should be occupied by scanning. Should be >= BLESCANINTERVAL.
|
|
* Scan interval is how long scanning should be done on each channel. BLE uses 3 channels for advertising.
|
|
* -> Adjust these values with power consumption in mind if power is limited.
|
|
* -> Scan interval can be changed during runtime by remote comammand.
|
|
*/
|
|
|
|
// WiFi scan parameters
|
|
#define WIFI_CHANNEL_MIN 1 // start channel number where scan begings
|
|
#define WIFI_CHANNEL_MAX 13 // total channel number to scan
|
|
#define WIFI_MY_COUNTRY "EU" // select locale for Wifi RF settings
|
|
#define WIFI_CHANNEL_SWITCH_INTERVAL 50 // [seconds/100] -> 0,5 sec.
|
|
|
|
// LoRa payload default parameters
|
|
#define MEM_LOW 2048 // [Bytes] low memory threshold triggering a send cycle
|
|
#define RETRANSMIT_RCMD 5 // [seconds] wait time before retransmitting rcommand results
|
|
#define PAYLOAD_BUFFER_SIZE 51 // maximum size of payload block per transmit
|
|
#define LORASFDEFAULT 9 // 7 ... 12 SF, according to LoRaWAN specs
|
|
#define MAXLORARETRY 500 // maximum count of TX retries if LoRa busy
|
|
#define SEND_QUEUE_SIZE 10 // maximum number of messages in payload send queue
|
|
|
|
// Ports on which the device sends and listenes on LoRaWAN and SPI
|
|
#define COUNTERPORT 1 // Port on which device sends counts
|
|
#define RCMDPORT 2 // Port on which device listenes for remote commands
|
|
#define STATUSPORT 2 // Port on which device sends remote command results
|
|
#define CONFIGPORT 3 // Port on which device sends config query results
|
|
#define GPSPORT 4 // Port on which device sends gps query results
|
|
#define BUTTONPORT 5 // Port on which device sends button pressed signal
|
|
#define LPP1PORT 1 // Port for Cayenne LPP 1.0 dynamic sensor encoding
|
|
#define LPP2PORT 2 // Port for Cayenne LPP 2.0 packed sensor encoding
|
|
#define BEACONPORT 6 // Port on which device sends beacon alarms
|
|
|
|
// Some hardware settings
|
|
#define RGBLUMINOSITY 30 // RGB LED luminosity [default = 30%]
|
|
#define DISPLAYREFRESH_MS 40 // OLED refresh cycle in ms [default = 40] -> 1000/40 = 25 frames per second
|
|
#define HOMECYCLE 30 // house keeping cycle in seconds [default = 30 secs]
|
|
|
|
// OTA settings
|
|
#define USE_OTA 1 // Comment out to disable OTA update
|
|
#define WIFI_MAX_TRY 5 // maximum number of wifi connect attempts for OTA update [default = 20]
|
|
#define OTA_MAX_TRY 3 // maximum number of attempts for OTA download and write to flash [default = 3]
|
|
#define OTA_MIN_BATT 3700 // minimum battery level for OTA [millivolt]
|
|
#define RESPONSE_TIMEOUT_MS 30000 // firmware binary server connection timeout [milliseconds]
|
|
|
|
// LMIC settings
|
|
// moved to src/lmic_config.h |