// ----- Paxcounter user config file ------
//
// --> adapt to your needs and use case <--
//
// Note: After editing, before "build", use "clean" button in PlatformIO!

#define PRODUCTNAME                     "PAXCNT"

// Verbose enables serial output
#define VERBOSE                         1       // comment out to silence the device, for mute use build option

// Payload send cycle and encoding
#define SEND_SECS                       30      // payload send cycle [seconds/2] -> 60 sec.
#define PAYLOAD_ENCODER                 2       // payload encoder: 1=Plain, 2=Packed, 3=CayenneLPP dynamic, 4=CayenneLPP packed

// Set this to include BLE counting and vendor filter functions
#define VENDORFILTER                    1       // comment out if you want to count things, not people
#define BLECOUNTER                      1       // comment out if you don't want BLE count, saves power & memory

// BLE scan parameters
#define BLESCANTIME                     0       // [seconds] scan duration, 0 means infinite [default], see note below
#define BLESCANWINDOW                   80      // [milliseconds] scan window, see below, 3 .. 10240, default 80ms
#define BLESCANINTERVAL                 80      // [illiseconds] scan interval, see below, 3 .. 10240, default 80ms = 100% duty cycle

/* Note: guide for setting bluetooth parameters
*
* |< Scan Window >       |< Scan Window >       | ... |< Scan Window >       |
* |<    Scan Interval   >|<    Scan Interval   >| ... |<    Scan Interval   >|
* |<                   Scan duration                                        >|
* 
* Scan duration sets how long scanning should be going on, before starting a new scan cycle. 0 means infinite (default).
* Scan window sets how much of the interval should be occupied by scanning. Should be >= BLESCANINTERVAL.
* Scan interval is how long scanning should be done on each channel. BLE uses 3 channels for advertising.
* -> Adjust these values with power consumption in mind if power is limited.
* -> Scan interval can be changed during runtime by remote comammand.
*/

// WiFi scan parameters
#define WIFI_CHANNEL_MIN                1       // start channel number where scan begings
#define	WIFI_CHANNEL_MAX                13      // total channel number to scan
#define WIFI_MY_COUNTRY                 "EU"    // select locale for Wifi RF settings
#define	WIFI_CHANNEL_SWITCH_INTERVAL    50      // [seconds/100] -> 0,5 sec.

// LoRa payload default parameters
#define MEM_LOW                         2048    // [Bytes] low memory threshold triggering a send cycle
#define RETRANSMIT_RCMD                 5       // [seconds] wait time before retransmitting rcommand results
#define PAYLOAD_BUFFER_SIZE             51      // maximum size of payload block per transmit
#define LORASFDEFAULT                   9       // 7 ... 12 SF, according to LoRaWAN specs
#define MAXLORARETRY                    500     // maximum count of TX retries if LoRa busy
#define SEND_QUEUE_SIZE                 10      // maximum number of messages in payload send queue

// Ports on which the device sends and listenes on LoRaWAN and SPI
#define COUNTERPORT                     1       // Port on which device sends counts
#define RCMDPORT                        2       // Port on which device listenes for remote commands
#define STATUSPORT                      2       // Port on which device sends remote command results
#define CONFIGPORT                      3       // Port on which device sends gps query results
#define GPSPORT                         4       // Port on which device sends gps query results
#define BUTTONPORT                      5       // Port on which device sends button pressed signal
#define LPP1PORT                        1       // Port for Cayenne LPP 1.0 dynamic sensor encoding
#define LPP2PORT                        2       // Port for Cayenne LPP 2.0 packed sensor encoding
#define BEACONPORT                      6       // Port on which device sends beacon alarms

// Some hardware settings
#define RGBLUMINOSITY                   30      // RGB LED luminosity [default = 30%]
#define DISPLAYREFRESH_MS               40      // OLED refresh cycle in ms [default = 40] -> 1000/40 = 25 frames per second
#define HOMECYCLE                       30      // house keeping cycle in seconds [default = 30 secs]

// OTA settings
#define WIFI_MAX_TRY                    20      // maximum number of wifi connect attempts for OTA update [default = 20]

// LMIC settings
// define hardware independent LMIC settings here, settings of standard library in /lmic/config.h will be ignored
// define hardware specifics settings in platformio.ini as build_flag for hardware environment

// Select frequency band here according to national regulations
#define CFG_eu868 1
//#define CFG_us915 1

// This is the SX1272/SX1273 radio, which is also used on the HopeRF
// RFM92 boards.
//#define CFG_sx1272_radio 1
// This is the SX1276/SX1277/SX1278/SX1279 radio, which is also used on
// the HopeRF RFM95 boards.
//#define CFG_sx1276_radio 1

// 16 μs per tick
// LMIC requires ticks to be 15.5μs - 100 μs long
#define US_PER_OSTICK_EXPONENT 4
#define US_PER_OSTICK (1 << US_PER_OSTICK_EXPONENT)
#define OSTICKS_PER_SEC (1000000 / US_PER_OSTICK)

// Set this to 1 to enable some basic debug output (using printf) about
// RF settings used during transmission and reception. Set to 2 to
// enable more verbose output. Make sure that printf is actually
// configured (e.g. on AVR it is not by default), otherwise using it can
// cause crashing.
//#define LMIC_DEBUG_LEVEL 1

// Enable this to allow using printf() to print to the given serial port
// (or any other Print object). This can be easy for debugging. The
// current implementation only works on AVR, though.
//#define LMIC_PRINTF_TO Serial

// Any runtime assertion failures are printed to this serial port (or
// any other Print object). If this is unset, any failures just silently
// halt execution.
#define LMIC_FAILURE_TO Serial

// Uncomment this to disable all code related to joining
//#define DISABLE_JOIN
// Uncomment this to disable all code related to ping
#define DISABLE_PING
// Uncomment this to disable all code related to beacon tracking.
// Requires ping to be disabled too
#define DISABLE_BEACONS

// Uncomment these to disable the corresponding MAC commands.
// Class A
//#define DISABLE_MCMD_DCAP_REQ // duty cycle cap
//#define DISABLE_MCMD_DN2P_SET // 2nd DN window param
//#define DISABLE_MCMD_SNCH_REQ // set new channel
// Class B
//#define DISABLE_MCMD_PING_SET // set ping freq, automatically disabled by DISABLE_PING
//#define DISABLE_MCMD_BCNI_ANS // next beacon start, automatical disabled by DISABLE_BEACON

// In LoRaWAN, a gateway applies I/Q inversion on TX, and nodes do the
// same on RX. This ensures that gateways can talk to nodes and vice
// versa, but gateways will not hear other gateways and nodes will not
// hear other nodes. By uncommenting this macro, this inversion is
// disabled and this node can hear other nodes. If two nodes both have
// this macro set, they can talk to each other (but they can no longer
// hear gateways). This should probably only be used when debugging
// and/or when talking to the radio directly (e.g. like in the "raw"
// example).
//#define DISABLE_INVERT_IQ_ON_RX

// This allows choosing between multiple included AES implementations.
// Make sure exactly one of these is uncommented.
//
// This selects the original AES implementation included LMIC. This
// implementation is optimized for speed on 32-bit processors using
// fairly big lookup tables, but it takes up big amounts of flash on the
// AVR architecture.
#define USE_ORIGINAL_AES
//
// This selects the AES implementation written by Ideetroon for their
// own LoRaWAN library. It also uses lookup tables, but smaller
// byte-oriented ones, making it use a lot less flash space (but it is
// also about twice as slow as the original).
// #define USE_IDEETRON_AES