// ----- Paxcounter user config file ------ // // --> adapt to your needs and use case <-- // // Note: After editing, before "build", use "clean" button in PlatformIO! #define PRODUCTNAME "PAXCNT" // Verbose enables serial output #define VERBOSE 1 // comment out to silence the device, for mute use build option // Payload send cycle and encoding #define SEND_SECS 30 // payload send cycle [seconds/2] -> 60 sec. #define PAYLOAD_ENCODER 2 // payload encoder: 1=Plain, 2=Packed, 3=CayenneLPP dynamic, 4=CayenneLPP packed // Set this to include BLE counting and vendor filter functions #define VENDORFILTER 1 // comment out if you want to count things, not people #define BLECOUNTER 1 // activate if you want to use BLE count, at expense of memory // BLE scan parameters #define BLESCANTIME 0 // [seconds] scan duration, 0 means infinite [default], see note below #define BLESCANWINDOW 80 // [milliseconds] scan window, see below, 3 .. 10240, default 80ms #define BLESCANINTERVAL 80 // [illiseconds] scan interval, see below, 3 .. 10240, default 80ms = 100% duty cycle /* Note: guide for setting bluetooth parameters * * |< Scan Window > |< Scan Window > | ... |< Scan Window > | * |< Scan Interval >|< Scan Interval >| ... |< Scan Interval >| * |< Scan duration >| * * Scan duration sets how long scanning should be going on, before starting a new scan cycle. 0 means infinite (default). * Scan window sets how much of the interval should be occupied by scanning. Should be >= BLESCANINTERVAL. * Scan interval is how long scanning should be done on each channel. BLE uses 3 channels for advertising. * -> Adjust these values with power consumption in mind if power is limited. * -> Scan interval can be changed during runtime by remote comammand. */ // WiFi scan parameters #define WIFI_CHANNEL_MIN 1 // start channel number where scan begings #define WIFI_CHANNEL_MAX 13 // total channel number to scan #define WIFI_MY_COUNTRY "EU" // select locale for Wifi RF settings #define WIFI_CHANNEL_SWITCH_INTERVAL 50 // [seconds/100] -> 0,5 sec. // LoRa payload default parameters #define MEM_LOW 2048 // [Bytes] low memory threshold triggering a send cycle #define RETRANSMIT_RCMD 5 // [seconds] wait time before retransmitting rcommand results #define PAYLOAD_BUFFER_SIZE 51 // maximum size of payload block per transmit #define LORASFDEFAULT 9 // 7 ... 12 SF, according to LoRaWAN specs #define MAXLORARETRY 500 // maximum count of TX retries if LoRa busy #define SEND_QUEUE_SIZE 10 // maximum number of messages in payload send queue // Ports on which the device sends and listenes on LoRaWAN and SPI #define COUNTERPORT 1 // Port on which device sends counts #define RCMDPORT 2 // Port on which device listenes for remote commands #define STATUSPORT 2 // Port on which device sends remote command results #define CONFIGPORT 3 // Port on which device sends config query results #define GPSPORT 4 // Port on which device sends gps data #define BUTTONPORT 5 // Port on which device sends button pressed signal #define LPP1PORT 1 // Port for Cayenne LPP 1.0 dynamic sensor encoding #define LPP2PORT 2 // Port for Cayenne LPP 2.0 packed sensor encoding #define BEACONPORT 6 // Port on which device sends beacon alarms #define BMEPORT 7 // Port on which device sends BME680 sensor data #define BATTPORT 8 // Port on which device sends battery voltage data #define SENSOR1PORT 10 // Port on which device sends User sensor #1 data #define SENSOR2PORT 11 // Port on which device sends User sensor #2 data #define SENSOR3PORT 12 // Port on which device sends User sensor #3 data // Some hardware settings #define RGBLUMINOSITY 30 // RGB LED luminosity [default = 30%] #define DISPLAYREFRESH_MS 40 // OLED refresh cycle in ms [default = 40] -> 1000/40 = 25 frames per second #define HOMECYCLE 30 // house keeping cycle in seconds [default = 30 secs] // Settings for BME680 environmental sensor (if present) #define BME_TEMP_OFFSET 5.0f // Offset sensor on chip temp <-> ambient temp [default = 5°C] #define STATE_SAVE_PERIOD UINT32_C(360 * 60 * 1000) // update every 360 minutes = 4 times a day // OTA settings #define USE_OTA 1 // Comment out to disable OTA update #define WIFI_MAX_TRY 5 // maximum number of wifi connect attempts for OTA update [default = 20] #define OTA_MAX_TRY 5 // maximum number of attempts for OTA download and write to flash [default = 3] #define OTA_MIN_BATT 3600 // minimum battery level for OTA [millivolt] #define RESPONSE_TIMEOUT_MS 60000 // firmware binary server connection timeout [milliseconds] // settings for syncing time of node and external time sources #define TIME_SYNC_INTERVAL_GPS 60 // sync time each ... minutes with GPS [default = 60], comment out means off #define TIME_SYNC_INTERVAL_RTC 60 // sync time each ... minutes with RTC [default = 60], comment out means off //#define TIME_SYNC_INTERVAL_LORA 60 // sync time each ... minutes with LORA network [default = 60], comment out means off #define IF482_OFFSET 984 // 1sec minus IF482 serial transmit time [ms]: e.g. 9 bits * 17 bytes * 1/9600 bps = 16ms // time zone, see https://github.com/JChristensen/Timezone/blob/master/examples/WorldClock/WorldClock.ino #define DAYLIGHT_TIME {"CEST", Last, Sun, Mar, 2, 120} // Central European Summer Time #define STANDARD_TIME {"CET ", Last, Sun, Oct, 3, 60} // Central European Standard Time // LMIC settings // moved to src/lmic_config.h