// ----- Paxcounter user config file ------ // // --> adapt to your needs and use case <-- // // Note: After editing, before "build", use "clean" button in PlatformIO! #define PRODUCTNAME "PAXCNT" // Verbose enables serial output #define VERBOSE 1 // set to 0 to silence the device, for mute use build option // Payload send cycle and encoding #define SENDCYCLE 30 // payload send cycle [seconds/2], 0 .. 255 #define PAYLOAD_ENCODER 2 // payload encoder: 1=Plain, 2=Packed, 3=Cayenne LPP dynamic, 4=Cayenne LPP packed // Set this to include BLE counting and vendor filter functions, or to switch off WIFI counting #define VENDORFILTER 1 // set to 0 if you want to count things, not people #define BLECOUNTER 0 // set it to 1 if you want to use BLE count, at expense of power & memory #define WIFICOUNTER 1 // set it to 0 if you want to switch off WIFI count // BLE scan parameters #define BLESCANTIME 0 // [seconds] scan duration, 0 means infinite [default], see note below #define BLESCANWINDOW 80 // [milliseconds] scan window, see below, 3 .. 10240, default 80ms #define BLESCANINTERVAL 80 // [illiseconds] scan interval, see below, 3 .. 10240, default 80ms = 100% duty cycle /* Note: guide for setting bluetooth parameters * * |< Scan Window > |< Scan Window > | ... |< Scan Window > | * |< Scan Interval >|< Scan Interval >| ... |< Scan Interval >| * |< Scan duration >| * * Scan duration sets how long scanning should be going on, before starting a new scan cycle. 0 means infinite (default). * Scan window sets how much of the interval should be occupied by scanning. Should be >= BLESCANINTERVAL. * Scan interval is how long scanning should be done on each channel. BLE uses 3 channels for advertising. * -> Adjust these values with power consumption in mind if power is limited. * -> Scan interval can be changed during runtime by remote comammand. */ // WiFi scan parameters #define WIFI_CHANNEL_MIN 1 // start channel number where scan begings #define WIFI_CHANNEL_MAX 13 // total channel number to scan #define WIFI_MY_COUNTRY "EU" // select locale for Wifi RF settings #define WIFI_CHANNEL_SWITCH_INTERVAL 50 // [seconds/100] -> 0,5 sec. // LoRa payload default parameters #define MEM_LOW 2048 // [Bytes] low memory threshold triggering a send cycle #define RETRANSMIT_RCMD 5 // [seconds] wait time before retransmitting rcommand results #define PAYLOAD_BUFFER_SIZE 51 // maximum size of payload block per transmit #define LORASFDEFAULT 9 // 7 ... 12 SF, according to LoRaWAN specs #define MAXLORARETRY 500 // maximum count of TX retries if LoRa busy #define SEND_QUEUE_SIZE 10 // maximum number of messages in payload send queue [1 = no queue] // Hardware settings #define RGBLUMINOSITY 30 // RGB LED luminosity [default = 30%] #define DISPLAYREFRESH_MS 40 // OLED refresh cycle in ms [default = 40] -> 1000/40 = 25 frames per second #define HOMECYCLE 30 // house keeping cycle in seconds [default = 30 secs] // Settings for BME680 environmental sensor #define BME_TEMP_OFFSET 5.0f // Offset sensor on chip temp <-> ambient temp [default = 5°C] #define STATE_SAVE_PERIOD UINT32_C(360 * 60 * 1000) // update every 360 minutes = 4 times a day // OTA settings #define USE_OTA 1 // set to 0 to disable OTA update #define WIFI_MAX_TRY 5 // maximum number of wifi connect attempts for OTA update [default = 20] #define OTA_MAX_TRY 5 // maximum number of attempts for OTA download and write to flash [default = 3] #define OTA_MIN_BATT 3600 // minimum battery level for OTA [millivolt] #define RESPONSE_TIMEOUT_MS 60000 // firmware binary server connection timeout [milliseconds] // settings for syncing time of node with external time source #define TIME_SYNC_INTERVAL 60 // sync time attempt each .. minutes from time source (GPS/LORA/RTC) [default = 60], 0 means off #define TIME_SYNC_INTERVAL_RETRY 10 // retry time sync after lost sync each .. minutes [default = 10], 0 means off #define TIME_SYNC_COMPILEDATE 0 // set to 1 to use compile date to initialize RTC after power outage [default = 0] #define TIME_SYNC_LORAWAN 0 // set to 1 to use LORA network as time source, 0 means off [default = 0] #define TIME_SYNC_LORASERVER 1 // set to 1 to use LORA timeserver as time source, 0 means off [default = 0] // settings for syncing time with timeserver applications #define TIME_SYNC_SAMPLES 1 // number of time requests for averaging #define TIME_SYNC_CYCLE 60 // delay between two time samples [seconds] #define TIME_SYNC_TIMEOUT 300 // timeout waiting for timeserver answer [seconds] // time zone, see https://github.com/JChristensen/Timezone/blob/master/examples/WorldClock/WorldClock.ino #define DAYLIGHT_TIME {"CEST", Last, Sun, Mar, 2, 120} // Central European Summer Time #define STANDARD_TIME {"CET ", Last, Sun, Oct, 3, 60} // Central European Standard Time // Ports on which the device sends and listenes on LoRaWAN and SPI #define COUNTERPORT 1 // counts #define RCMDPORT 2 // remote commands #define STATUSPORT 2 // remote command results #define CONFIGPORT 3 // config query results #define GPSPORT 4 // gps #define BUTTONPORT 5 // button pressed signal #define BEACONPORT 6 // beacon alarms #define BMEPORT 7 // BME680 sensor #define BATTPORT 8 // battery voltage #define TIMEPORT 9 // time query #define TIMEANSWERPORT_MIN 0xA0 // time answer, start of port range #define TIMEANSWERPORT_MAX 0xDF // time answer, end of port range #define SENSOR1PORT 10 // user sensor #1 #define SENSOR2PORT 11 // user sensor #2 #define SENSOR3PORT 12 // user sensor #3 // Cayenne LPP Ports, see https://community.mydevices.com/t/cayenne-lpp-2-0/7510 #define CAYENNE_LPP1 1 // dynamic sensor payload (LPP 1.0) #define CAYENNE_LPP2 2 // packed sensor payload (LPP 2.0) #define CAYENNE_GPS 3 // full scale GPS payload #define CAYENNE_ACTUATOR 10 // actuator commands #define CAYENNE_DEVICECONFIG 11 // device period configuration #define CAYENNE_SENSORREAD 13 // sensor period configuration #define CAYENNE_SENSORENABLE 14 // sensor enable configuration