Merge branch 'master-1.7.0-rc2' into development
This commit is contained in:
commit
ffab2f7743
@ -24,5 +24,12 @@
|
|||||||
// additional definitions for LMIC
|
// additional definitions for LMIC
|
||||||
#define LORA_IO1 (33)
|
#define LORA_IO1 (33)
|
||||||
#define LORA_IO2 LMIC_UNUSED_PIN
|
#define LORA_IO2 LMIC_UNUSED_PIN
|
||||||
|
#define LORA_SCK (5)
|
||||||
|
#define LORA_MOSI (27)
|
||||||
|
#define LORA_MISO (19)
|
||||||
|
#define LORA_CS (18)
|
||||||
|
#define LORA_RST (14)
|
||||||
|
#define LORA_IRQ (26)
|
||||||
|
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
@ -26,5 +26,11 @@
|
|||||||
// additional definitions for LMIC
|
// additional definitions for LMIC
|
||||||
#define LORA_IO1 (35)
|
#define LORA_IO1 (35)
|
||||||
#define LORA_IO2 (34)
|
#define LORA_IO2 (34)
|
||||||
|
#define LORA_SCK (5)
|
||||||
|
#define LORA_MOSI (27)
|
||||||
|
#define LORA_MISO (19)
|
||||||
|
#define LORA_CS (18)
|
||||||
|
#define LORA_RST (14)
|
||||||
|
#define LORA_IRQ (26)
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
@ -1,37 +1,37 @@
|
|||||||
// clang-format off
|
// clang-format off
|
||||||
|
|
||||||
#ifndef _LOPY_H
|
#ifndef _LOPY_H
|
||||||
#define _LOPY_H
|
#define _LOPY_H
|
||||||
|
|
||||||
#include <stdint.h>
|
#include <stdint.h>
|
||||||
|
|
||||||
// Hardware related definitions for Pycom LoPy Board (NOT LoPy4)
|
// Hardware related definitions for Pycom LoPy Board (NOT LoPy4)
|
||||||
|
|
||||||
#define HAS_LORA 1 // comment out if device shall not send data via LoRa
|
#define HAS_LORA 1 // comment out if device shall not send data via LoRa
|
||||||
#define CFG_sx1272_radio 1
|
#define CFG_sx1272_radio 1
|
||||||
#define HAS_LED NOT_A_PIN // LoPy4 has no on board mono LED, we use on board RGB LED
|
#define HAS_LED NOT_A_PIN // LoPy4 has no on board mono LED, we use on board RGB LED
|
||||||
#define HAS_RGB_LED (0) // WS2812B RGB LED on GPIO0
|
#define HAS_RGB_LED (0) // WS2812B RGB LED on GPIO0
|
||||||
|
|
||||||
// Pins for LORA chip SPI interface come from board file, we need some
|
// Pins for LORA chip SPI interface come from board file, we need some
|
||||||
// additional definitions for LMIC
|
// additional definitions for LMIC
|
||||||
#define LORA_IRQ (23)
|
#define LORA_IRQ (23)
|
||||||
|
|
||||||
// select WIFI antenna (internal = onboard / external = u.fl socket)
|
// select WIFI antenna (internal = onboard / external = u.fl socket)
|
||||||
#define HAS_ANTENNA_SWITCH (16) // pin for switching wifi antenna
|
#define HAS_ANTENNA_SWITCH (16) // pin for switching wifi antenna
|
||||||
#define WIFI_ANTENNA 0 // 0 = internal, 1 = external
|
#define WIFI_ANTENNA 0 // 0 = internal, 1 = external
|
||||||
|
|
||||||
// uncomment this only if your LoPy runs on a PYTRACK BOARD
|
// uncomment this only if your LoPy runs on a PYTRACK BOARD
|
||||||
#define HAS_GPS 1
|
#define HAS_GPS 1
|
||||||
#define GPS_I2C GPIO_NUM_25, GPIO_NUM_26 // SDA (P22), SCL (P21)
|
#define GPS_I2C GPIO_NUM_25, GPIO_NUM_26 // SDA (P22), SCL (P21)
|
||||||
#define GPS_ADDR 0x10
|
#define GPS_ADDR 0x10
|
||||||
|
|
||||||
// uncomment this only if your LoPy runs on a EXPANSION BOARD
|
// uncomment this only if your LoPy runs on a EXPANSION BOARD
|
||||||
//#define HAS_LED (12) // use if LoPy is on Expansion Board, this has a user LED
|
//#define HAS_LED (12) // use if LoPy is on Expansion Board, this has a user LED
|
||||||
//#define LED_ACTIVE_LOW 1 // use if LoPy is on Expansion Board, this has a user LED
|
//#define LED_ACTIVE_LOW 1 // use if LoPy is on Expansion Board, this has a user LED
|
||||||
//#define HAS_BUTTON (13) // user button on expansion board
|
//#define HAS_BUTTON (13) // user button on expansion board
|
||||||
//#define BUTTON_PULLUP 1 // Button need pullup instead of default pulldown
|
//#define BUTTON_PULLUP 1 // Button need pullup instead of default pulldown
|
||||||
//#define HAS_BATTERY_PROBE ADC1_GPIO39_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
|
//#define HAS_BATTERY_PROBE ADC1_GPIO39_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
|
||||||
//#define BATT_FACTOR 2 // voltage divider 1MOhm/1MOhm -> expansion board 3.0
|
//#define BATT_FACTOR 2 // voltage divider 1MOhm/1MOhm -> expansion board 3.0
|
||||||
//#define BATT_FACTOR 4 // voltage divider 115kOhm/56kOhm -> expansion board 2.0
|
//#define BATT_FACTOR 4 // voltage divider 115kOhm/56kOhm -> expansion board 2.0
|
||||||
|
|
||||||
#endif
|
#endif
|
||||||
|
@ -1,48 +1,48 @@
|
|||||||
// clang-format off
|
// clang-format off
|
||||||
|
|
||||||
#ifndef _LOPY4_H
|
#ifndef _LOPY4_H
|
||||||
#define _LOPY4_H
|
#define _LOPY4_H
|
||||||
|
|
||||||
#include <stdint.h>
|
#include <stdint.h>
|
||||||
|
|
||||||
// Hardware related definitions for Pycom LoPy4 Board
|
// Hardware related definitions for Pycom LoPy4 Board
|
||||||
|
|
||||||
#define HAS_LORA 1 // comment out if device shall not send data via LoRa
|
#define HAS_LORA 1 // comment out if device shall not send data via LoRa
|
||||||
|
|
||||||
//#defin HAS_SPI 1 // comment out if device shall not send data via SPI
|
//#defin HAS_SPI 1 // comment out if device shall not send data via SPI
|
||||||
// pin definitions for local wired SPI slave interface
|
// pin definitions for local wired SPI slave interface
|
||||||
//#define SPI_MOSI GPIO_NUM_22
|
//#define SPI_MOSI GPIO_NUM_22
|
||||||
//#define SPI_MISO GPIO_NUM_33
|
//#define SPI_MISO GPIO_NUM_33
|
||||||
//#define SPI_SCLK GPIO_NUM_26
|
//#define SPI_SCLK GPIO_NUM_26
|
||||||
//#define SPI_CS GPIO_NUM_36
|
//#define SPI_CS GPIO_NUM_36
|
||||||
|
|
||||||
#define CFG_sx1276_radio 1
|
#define CFG_sx1276_radio 1
|
||||||
//#define HAS_LED NOT_A_PIN // LoPy4 has no on board mono LED, we use on board RGB LED
|
//#define HAS_LED NOT_A_PIN // LoPy4 has no on board mono LED, we use on board RGB LED
|
||||||
#define HAS_RGB_LED (0) // WS2812B RGB LED on GPIO0 (P2)
|
#define HAS_RGB_LED (0) // WS2812B RGB LED on GPIO0 (P2)
|
||||||
#define BOARD_HAS_PSRAM // use extra 4MB extern RAM
|
#define BOARD_HAS_PSRAM // use extra 4MB extern RAM
|
||||||
|
|
||||||
// Pins for LORA chip SPI interface come from board file, we need some
|
// Pins for LORA chip SPI interface come from board file, we need some
|
||||||
// additional definitions for LMIC
|
// additional definitions for LMIC
|
||||||
#define LORA_IRQ (23)
|
#define LORA_IRQ (23)
|
||||||
#define LORA_RST NOT_A_PIN
|
#define LORA_RST NOT_A_PIN
|
||||||
#define SS 18
|
#define SS 18
|
||||||
|
|
||||||
// select WIFI antenna (internal = onboard / external = u.fl socket)
|
// select WIFI antenna (internal = onboard / external = u.fl socket)
|
||||||
#define HAS_ANTENNA_SWITCH (21) // pin for switching wifi antenna (P12)
|
#define HAS_ANTENNA_SWITCH (21) // pin for switching wifi antenna (P12)
|
||||||
#define WIFI_ANTENNA 0 // 0 = internal, 1 = external
|
#define WIFI_ANTENNA 0 // 0 = internal, 1 = external
|
||||||
|
|
||||||
// uncomment this only if your LoPy runs on a PYTRACK BOARD
|
// uncomment this only if your LoPy runs on a PYTRACK BOARD
|
||||||
//#define HAS_GPS 1
|
//#define HAS_GPS 1
|
||||||
//#define GPS_I2C GPIO_NUM_25, GPIO_NUM_26 // SDA (P22), SCL (P21)
|
//#define GPS_I2C GPIO_NUM_25, GPIO_NUM_26 // SDA (P22), SCL (P21)
|
||||||
//#define GPS_ADDR 0x10
|
//#define GPS_ADDR 0x10
|
||||||
|
|
||||||
// uncomment this only if your LoPy runs on a EXPANSION BOARD
|
// uncomment this only if your LoPy runs on a EXPANSION BOARD
|
||||||
#define HAS_LED (12) // use if LoPy is on Expansion Board, this has a user LED
|
#define HAS_LED (12) // use if LoPy is on Expansion Board, this has a user LED
|
||||||
#define LED_ACTIVE_LOW 1 // use if LoPy is on Expansion Board, this has a user LED
|
#define LED_ACTIVE_LOW 1 // use if LoPy is on Expansion Board, this has a user LED
|
||||||
#define HAS_BUTTON (13) // user button on expansion board
|
#define HAS_BUTTON (13) // user button on expansion board
|
||||||
#define BUTTON_PULLUP 1 // Button need pullup instead of default pulldown
|
#define BUTTON_PULLUP 1 // Button need pullup instead of default pulldown
|
||||||
#define HAS_BATTERY_PROBE ADC1_GPIO39_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
|
#define HAS_BATTERY_PROBE ADC1_GPIO39_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
|
||||||
#define BATT_FACTOR 2 // voltage divider 1MOhm/1MOhm -> expansion board 3.0
|
#define BATT_FACTOR 2 // voltage divider 1MOhm/1MOhm -> expansion board 3.0
|
||||||
//#define BATT_FACTOR 4 // voltage divider 115kOhm/56kOhm -> expansion board 2.0
|
//#define BATT_FACTOR 4 // voltage divider 115kOhm/56kOhm -> expansion board 2.0
|
||||||
|
|
||||||
#endif
|
#endif
|
Loading…
Reference in New Issue
Block a user