Merge remote-tracking branch 'upstream/master' into av/ttgo-t-wristband

README.md

@@ -48,6 +48,7 @@ LoLin32lite + [LoraNode32-Lite shield](https://github.com/hallard/LoLin32-Lite-L
 - Pyom: WiPy
 - WeMos: LoLin32, LoLin32 Lite, WeMos D32, [Wemos32 Oled](https://www.instructables.com/id/ESP32-With-Integrated-OLED-WEMOSLolin-Getting-Star/)
 - Crowdsupply: [TinyPICO](https://www.crowdsupply.com/unexpected-maker/tinypico)
+- TTGO: [T-Display](https://www.aliexpress.com/item/33048962331.html)
 - Generic ESP32
 
 Depending on board hardware following features are supported:

include/bmesensor.h

@@ -21,43 +21,29 @@ extern Ticker bmecycler;
 extern bmeStatus_t
     bme_status; // Make struct for storing gps data globally available
 
-// --- Bosch BSEC v1.4.7.4 library configuration ---
+// --- Bosch BSEC library configuration ---
-// 3,3V supply voltage; 3s max time between sensor_control calls; 4 days
+// We use 3,3V supply voltage; 3s max time between sensor_control calls; 4 days
 // calibration. Change this const if not applicable for your application (see
-// BME680 datasheet)
+// BME680 datasheet) Note: 3s max time must not exceed BMECYCLE frequency set in
-// Note: 3s max time not exceed BMECYCLE frequency set in paxcounter.conf!
+// paxcounter.conf!
-const uint8_t bsec_config_iaq[454] = {
+
-    4,   7,   4,   1,   61,  0,   0,   0,   0,   0,   0,   0,   174, 1,   0,
+const uint8_t bsec_config_iaq[] = {
-    0,   48,  0,   1,   0,   0,   192, 168, 71,  64,  49,  119, 76,  0,   0,
+#include "config/generic_33v_3s_4d/bsec_iaq.txt"
-    225, 68,  137, 65,  0,   63,  205, 204, 204, 62,  0,   0,   64,  63,  205,
+};
-    204, 204, 62,  0,   0,   0,   0,   216, 85,  0,   100, 0,   0,   0,   0,
+
-    0,   0,   0,   0,   28,  0,   2,   0,   0,   244, 1,   225, 0,   25,  0,
+/* Configure the BSEC library with information about the sensor
-    0,   128, 64,  0,   0,   32,  65,  144, 1,   0,   0,   112, 65,  0,   0,
+    18v/33v = Voltage at Vdd. 1.8V or 3.3V
-    0,   63,  16,  0,   3,   0,   10,  215, 163, 60,  10,  215, 35,  59,  10,
+    3s/300s = BSEC operating mode, BSEC_SAMPLE_RATE_LP or BSEC_SAMPLE_RATE_ULP
-    215, 35,  59,  9,   0,   5,   0,   0,   0,   0,   0,   1,   88,  0,   9,
+    4d/28d = Operating age of the sensor in days
-    0,   229, 208, 34,  62,  0,   0,   0,   0,   0,   0,   0,   0,   218, 27,
+    generic_18v_3s_4d
-    156, 62,  225, 11,  67,  64,  0,   0,   160, 64,  0,   0,   0,   0,   0,
+    generic_18v_3s_28d
-    0,   0,   0,   94,  75,  72,  189, 93,  254, 159, 64,  66,  62,  160, 191,
+    generic_18v_300s_4d
-    0,   0,   0,   0,   0,   0,   0,   0,   33,  31,  180, 190, 138, 176, 97,
+    generic_18v_300s_28d
-    64,  65,  241, 99,  190, 0,   0,   0,   0,   0,   0,   0,   0,   167, 121,
+    generic_33v_3s_4d
-    71,  61,  165, 189, 41,  192, 184, 30,  189, 64,  12,  0,   10,  0,   0,
+    generic_33v_3s_28d
-    0,   0,   0,   0,   0,   0,   0,   229, 0,   254, 0,   2,   1,   5,   48,
+    generic_33v_300s_4d
-    117, 100, 0,   44,  1,   112, 23,  151, 7,   132, 3,   197, 0,   92,  4,
+    generic_33v_300s_28d
-    144, 1,   64,  1,   64,  1,   144, 1,   48,  117, 48,  117, 48,  117, 48,
+*/
-    117, 100, 0,   100, 0,   100, 0,   48,  117, 48,  117, 48,  117, 100, 0,
-    100, 0,   48,  117, 48,  117, 100, 0,   100, 0,   100, 0,   100, 0,   48,
-    117, 48,  117, 48,  117, 100, 0,   100, 0,   100, 0,   48,  117, 48,  117,
-    100, 0,   100, 0,   44,  1,   44,  1,   44,  1,   44,  1,   44,  1,   44,
-    1,   44,  1,   44,  1,   44,  1,   44,  1,   44,  1,   44,  1,   44,  1,
-    44,  1,   8,   7,   8,   7,   8,   7,   8,   7,   8,   7,   8,   7,   8,
-    7,   8,   7,   8,   7,   8,   7,   8,   7,   8,   7,   8,   7,   8,   7,
-    112, 23,  112, 23,  112, 23,  112, 23,  112, 23,  112, 23,  112, 23,  112,
-    23,  112, 23,  112, 23,  112, 23,  112, 23,  112, 23,  112, 23,  255, 255,
-    255, 255, 255, 255, 255, 255, 220, 5,   220, 5,   220, 5,   255, 255, 255,
-    255, 255, 255, 220, 5,   220, 5,   255, 255, 255, 255, 255, 255, 255, 255,
-    255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255,
-    255, 255, 255, 255, 255, 255, 255, 255, 255, 44,  1,   0,   0,   0,   0,
-    138, 80,  0,   0};
 
 // Helper functions declarations
 int bme_init();

platformio_orig.ini

@@ -20,6 +20,7 @@ halfile = generic.h
 ;halfile = ttgofox.h
 ;halfile = ttgobeam.h
 ;halfile = ttgobeam10.h
+;halfile = ttgotdisplay.h
 ;halfile = fipy.h
 ;halfile = lopy.h
 ;halfile = lopy4.h
@@ -75,7 +76,8 @@ lib_deps_sensors =
     adafruit/Adafruit Unified Sensor @ ^1.1.4
     adafruit/Adafruit BME280 Library @ ^2.1.1
     adafruit/Adafruit BMP085 Library @ ^1.1.0
-    boschsensortec/BSEC Software Library @ 1.5.1474
+    ;boschsensortec/BSEC Software Library @ 1.6.1480
+    https://github.com/BoschSensortec/BSEC-Arduino-library.git
     https://github.com/ricki-z/SDS011.git
 lib_deps_basic =
     bblanchon/ArduinoJson @ <6

src/display.cpp

@@ -53,7 +53,7 @@ QRCode qrcode;
 #if (HAS_DISPLAY) == 1
 OBDISP ssoled;
 #elif (HAS_DISPLAY) == 2
-TFT_eSPI tft = TFT_eSPI();
+TFT_eSPI tft = TFT_eSPI(MY_DISPLAY_WIDTH, MY_DISPLAY_HEIGHT);
 #else
 #error Unknown display type specified in hal file
 #endif

src/hal/ttgotdisplay.h

@@ -0,0 +1,55 @@
+// clang-format off
+// upload_speed 1500000
+// board esp32dev
+
+#ifndef _TTGOTDISPLAY_H
+#define _TTGOTDISPLAY_H
+
+#include <stdint.h>
+
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_DISPLAY 2      // TFT-LCD, support work in progess, not ready yet
+#define MY_DISPLAY_FLIP  1 // use if display is rotated
+
+#define HAS_LED NOT_A_PIN  // no on board LED (?)
+#define HAS_BUTTON (35)    // on board button A
+
+// power management settings
+#define BAT_MEASURE_ADC ADC1_GPIO34_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_6
+#define BAT_VOLTAGE_DIVIDER 2.605f           // voltage divider
+
+// Display Settings
+#define MY_DISPLAY_WIDTH 135
+#define MY_DISPLAY_HEIGHT 240
+#define MY_DISPLAY_INVERT 1
+
+// setting for TTGO T-display
+#define USER_SETUP_LOADED 1
+#define ST7789_DRIVER 1
+
+#define CGRAM_OFFSET
+
+#define TFT_MOSI GPIO_NUM_19 // SPI
+#define TFT_SCLK GPIO_NUM_18 // SPI
+#define TFT_CS   GPIO_NUM_5  // Chip select control
+#define TFT_DC   GPIO_NUM_16 // Data Command control
+#define TFT_RST  GPIO_NUM_23 // Reset
+#define TFT_BL   GPIO_NUM_4  // LED back-light
+
+#define TFT_RGB_ORDER TFT_BGR  // Colour order Blue-Green-Red
+
+#define LOAD_GLCD   // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
+#define LOAD_FONT2  // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
+#define LOAD_FONT4  // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
+#define LOAD_FONT6  // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
+#define LOAD_FONT7  // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
+#define LOAD_FONT8  // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
+//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
+#define LOAD_GFXFF  // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
+#define SMOOTH_FONT
+
+#define SPI_FREQUENCY  40000000
+#define SPI_READ_FREQUENCY 6000000
+
+#endif

src/macsniff.cpp

@@ -134,7 +134,7 @@ uint16_t mac_analyze(MacBuffer_t MacBuffer) {
   uint32_t *oui; // temporary buffer for vendor OUI
   oui = (uint32_t *)MacBuffer.mac;
   // if we find OUI on vendor filter list we don't analyze and return early
-  if (std::find(vendors.begin(), vendors.end(), __builtin_bswap32(*oui) >> 8) !=
+  if (std::find(vendors.begin(), vendors.end(), __builtin_bswap32(*oui) >> 8) ==
       vendors.end())
     return 0;
 #endif

src/power.cpp

@@ -48,11 +48,9 @@ void AXP192_powerevent_IRQ(void) {
     ESP_LOGI(TAG, "Battery low temperature.");
 
   // short press -> esp32 deep sleep mode, can be exited by pressing user button
-#ifdef HAS_BUTTON
   if (pmu.isPEKShortPressIRQ() && (RTC_runmode == RUNMODE_NORMAL)) {
     enter_deepsleep(0, HAS_BUTTON);
   }
-#endif
 
   // long press -> shutdown power, can be exited by another longpress
   if (pmu.isPEKLongtPressIRQ()) {
@@ -89,6 +87,8 @@ void AXP192_power(pmu_power_t powerlevel) {
     pmu.setPowerOutPut(AXP192_LDO2, AXP202_ON);   // Lora on T-Beam V1.0
     pmu.setPowerOutPut(AXP192_LDO3, AXP202_ON);   // Gps on T-Beam V1.0
     pmu.setPowerOutPut(AXP192_DCDC1, AXP202_ON);  // OLED on T-Beam v1.0
+    pmu.setPowerOutPut(AXP192_DCDC2, AXP202_OFF); // unused on T-Beam v1.0
+    pmu.setPowerOutPut(AXP192_EXTEN, AXP202_OFF); // unused on T-Beam v1.0
     pmu.setChgLEDMode(AXP20X_LED_LOW_LEVEL);
     break;
   }
@@ -121,6 +121,8 @@ void AXP192_init(void) {
 
     // configure AXP192
     pmu.setDCDC1Voltage(3300);              // for external OLED display
+    pmu.setLDO2Voltage(3300);               // LORA VDD 3v3
+    pmu.setLDO3Voltage(3300);               // GPS VDD 3v3
     pmu.setTimeOutShutdown(false);          // no automatic shutdown
     pmu.setTSmode(AXP_TS_PIN_MODE_DISABLE); // TS pin mode off to save power
 
@@ -138,7 +140,8 @@ void AXP192_init(void) {
     attachInterrupt(digitalPinToInterrupt(PMU_INT), PMUIRQ, FALLING);
     pmu.enableIRQ(AXP202_VBUS_REMOVED_IRQ | AXP202_VBUS_CONNECT_IRQ |
                       AXP202_BATT_REMOVED_IRQ | AXP202_BATT_CONNECT_IRQ |
-                      AXP202_CHARGING_FINISHED_IRQ,
+                      AXP202_CHARGING_FINISHED_IRQ | AXP202_PEK_SHORTPRESS_IRQ |
+                      AXP202_PEK_LONGPRESS_IRQ,
                   1);
     pmu.clearIRQ();
 #endif // PMU_INT