BLE install logic changed (issue #612)

README.md

@@ -79,7 +79,7 @@ Some <b>3D printable cases</b> can be found (and, if wanted so, ordered) on Thin
 for example.<br>
 
 <b>Power consumption</b> was metered at around 450 - 1000mW, depending on board and user settings in paxcounter.conf.
-By default bluetooth sniffing is disabled (#define *BLECOUNTER* 0 in paxcounter.conf). Enabling bluetooth costs 30% more power + 30% flash storage for the software stack. Proof of concept showed that for passenger flow metering wifi sniffing shows better results than bluetooth sniffing. If you enable bluetooth be aware that this goes on expense of wifi sniffing results, because then wifi and bt stack must share the 2,4 GHz RF ressources of ESP32. If you need to sniff wifi and bt in parallel and need best possible results, use two boards - one for wifi only and one for bt only - and add counted results.
+By default bluetooth sniffing not installed (#define *BLECOUNTER* 0 in paxcounter.conf). Installing and enabling bluetooth costs 30% more power + 30% flash storage for the software stack. If you enable bluetooth be aware that this goes on expense of wifi sniffing results, because then wifi and bt stack must share the 2,4 GHz RF ressources of ESP32. If you need to sniff wifi and bt in parallel and need best possible results, use two boards - one for wifi only and one for bt only - and add counted results.
 
 # Preparing
 

src/configmanager.cpp

@@ -29,8 +29,8 @@ void defaultConfig() {
   cfg.blescantime =
       BLESCANINTERVAL /
       10; // BT channel scan cycle [seconds/100], default 1 (= 10ms)
-  cfg.blescan = BLECOUNTER;        // 0=disabled, 1=enabled
+  cfg.blescan = 1;                 // 0=disabled, 1=enabled
-  cfg.wifiscan = WIFICOUNTER;      // 0=disabled, 1=enabled
+  cfg.wifiscan = 1;                // 0=disabled, 1=enabled
   cfg.wifiant = 0;                 // 0=internal, 1=external (for LoPy/LoPy4)
   cfg.vendorfilter = VENDORFILTER; // 0=disabled, 1=enabled
   cfg.rgblum = RGBLUMINOSITY;      // RGB Led luminosity (0..100%)

src/main.cpp

@@ -315,9 +315,9 @@ void setup() {
 #if (HAS_SENSOR_1)
 #if (COUNT_ENS)
   ESP_LOGI(TAG, "init CWA-counter");
-  if ( cwa_init() )
+  if (cwa_init())
-      strcat_P(features, " CWA");
+    strcat_P(features, " CWA");
-#else        
+#else
   strcat_P(features, " SENS(1)");
   sensor_init();
 #endif
@@ -402,8 +402,13 @@ void setup() {
 #if (WIFICOUNTER)
   strcat_P(features, " WIFI");
   // start wifi in monitor mode and start channel rotation timer
-  ESP_LOGI(TAG, "Starting Wifi...");
+
   wifi_sniffer_init();
+  if (cfg.blescan) {
+    ESP_LOGI(TAG, "Starting Wifi...");
+    switch_wifi_sniffer(1);
+  } else
+    switch_wifi_sniffer(0);
 #else
   // switch off wifi
   esp_wifi_deinit();

src/paxcounter.conf

@@ -7,17 +7,17 @@
 // Note: After editing, before "build", use "clean" button in PlatformIO!
 
 // Verbose enables additional serial debug output
-#define VERBOSE                         0       // set to 0 to silence the device, for mute use build option
+#define VERBOSE                         1       // set to 0 to silence the device, for mute use build option
 
 // Payload send cycle and encoding
 #define SENDCYCLE                       30      // payload send cycle [seconds/2], 0 .. 255
 #define PAYLOAD_ENCODER                 2       // payload encoder: 1=Plain, 2=Packed, 3=Cayenne LPP dynamic, 4=Cayenne LPP packed
-#define COUNTERMODE                     0       // 0=cyclic, 1=cumulative, 2=cyclic confirmed
+#define COUNTERMODE                     1       // 0=cyclic, 1=cumulative, 2=cyclic confirmed
 
 // Set this to include BLE counting and vendor filter functions, or to switch off WIFI counting
 #define VENDORFILTER                    0       // set to 0 if you want to scan all devices, not filtering smartphone OUIs
-#define BLECOUNTER                      0       // set it to 1 if you want to use BLE count, at expense of power & memory
+#define BLECOUNTER                      0       // set to 0 if you do not want to install the BLE sniffer
-#define WIFICOUNTER                     1       // set it to 0 if you want to switch off WIFI count
+#define WIFICOUNTER                     1       // set to 0 if you do not want to install the WIFI sniffer
 
 // BLE scan parameters
 #define BLESCANTIME                     0       // [seconds] scan duration, 0 means infinite [default], see note below

src/wifiscan.cpp

@@ -73,14 +73,12 @@ void wifi_sniffer_init(void) {
   ESP_ERROR_CHECK(esp_wifi_set_ps(WIFI_PS_NONE)); // no modem power saving
   ESP_ERROR_CHECK(esp_wifi_set_promiscuous_filter(&filter)); // set frame filter
   ESP_ERROR_CHECK(esp_wifi_set_promiscuous_rx_cb(&wifi_sniffer_packet_handler));
-  ESP_ERROR_CHECK(esp_wifi_start());               // for esp_wifi v3.3
   ESP_ERROR_CHECK(esp_wifi_set_promiscuous(true)); // now switch on monitor mode
 
   // setup wifi channel rotation timer
   WifiChanTimer =
       xTimerCreate("WifiChannelTimer", pdMS_TO_TICKS(cfg.wifichancycle * 10),
                    pdTRUE, (void *)0, switchWifiChannel);
-  switch_wifi_sniffer(1);
 }
 
 void switch_wifi_sniffer(uint8_t state) {