Merge pull request #883 from cyberman54/master

sync dev to master

README.md

@@ -22,7 +22,7 @@ Paxcounter is an [ESP32](https://www.espressif.com/en/products/socs/esp32) MCU b
 
 Intention of this project is to do this without intrusion in privacy: You don't need to track people owned devices, if you just want to count them. Therefore, Paxcounter does not persistenly store MAC adresses and does no kind of fingerprinting the scanned devices.
 
-Data can either be be stored on a local SD-card, transferred to cloud using LoRaWAN network or MQTT over TCP/IP, or transmitted to a local host using serial (SPI) interface.
+Data can either be be stored on a local SD-card, transferred to cloud using LoRaWAN network (e.g. TheThingsNetwork or Helium) or MQTT over TCP/IP, or transmitted to a local host using serial (SPI) interface.
 
 You can build this project battery powered using ESP32 deep sleep mode and reach long uptimes with a single 18650 Li-Ion cell.
 
@@ -82,7 +82,7 @@ Some <b>3D printable cases</b> can be found (and, if wanted so, ordered) on Thin
 for example.<br>
 
 <b>Power consumption</b> was metered at around 450 - 1000mW, depending on board and user settings in paxcounter.conf.
-By default bluetooth sniffing not installed (#define *BLECOUNTER* 0 in paxcounter.conf). Installing and enabling bluetooth costs 30% more power + 30% flash storage for the software stack. If you enable bluetooth be aware that this goes on expense of wifi sniffing results, because then wifi and bt stack must share the 2,4 GHz RF ressources of ESP32. If you need to sniff wifi and bt in parallel and need best possible results, use two boards - one for wifi only and one for bt only - and add counted results.
+By default bluetooth sniffing not installed (#define *BLECOUNTER* 0 in paxcounter.conf). If you enable bluetooth be aware that this goes on expense of wifi sniffing results, because then wifi and bt stack must share the 2,4 GHz RF ressources of ESP32. If you need to sniff wifi and bt in parallel and need best possible results, use two boards - one for wifi only and one for bt only - and add counted results.
 
 # Preparing
 
@@ -98,7 +98,7 @@ Edit `platformio_orig.ini` and select desired hardware target in section boards.
 ## paxcounter.conf
 Edit `src/paxcounter_orig.conf` and tailor settings in this file according to your needs and use case. Please take care of the duty cycle regulations of the LoRaWAN network you're going to use. Copy or rename to `src/paxcounter.conf`.
 
-If your device has a **real time clock** it can be updated bei either LoRaWAN network or GPS time, according to settings *TIME_SYNC_INTERVAL* and *TIME_SYNC_LORAWAN* in `paxcounter.conf`.
+If your device has a **real time clock** it can be updated by either LoRaWAN network or GPS time, according to settings *TIME_SYNC_INTERVAL* and *TIME_SYNC_LORAWAN* in `paxcounter.conf`.
 
 ## src/lmic_config.h
 Edit `src/lmic_config.h` and tailor settings in this file according to your country and device hardware. Please take care of national regulations when selecting the frequency band for LoRaWAN.

include/display.h

@@ -14,14 +14,17 @@
 #endif
 
 #define DISPLAY_PAGES (7) // number of paxcounter display pages
+#define PLOTBUFFERSIZE (MY_DISPLAY_WIDTH * MY_DISPLAY_HEIGHT / 8)
 
 // settings for OLED display library
 #if (HAS_DISPLAY) == 1
-#define MY_FONT_SMALL FONT_SMALL
+#define MY_FONT_SMALL FONT_6x8
-#define MY_FONT_NORMAL FONT_NORMAL
+#define MY_FONT_NORMAL FONT_8x8
-#define MY_FONT_LARGE FONT_LARGE
+#define MY_FONT_LARGE FONT_16x32
-#define MY_FONT_STRETCHED FONT_STRETCHED
+#define MY_FONT_STRETCHED FONT_12x16
-#define USE_BACKBUFFER 1
+
+#define MY_DISPLAY_FIRSTLINE 30
+
 #ifdef MY_DISPLAY_ADDR
 #define OLED_ADDR MY_DISPLAY_ADDR
 #else
@@ -33,6 +36,12 @@
 #ifndef OLED_FREQUENCY
 #define OLED_FREQUENCY 400000L
 #endif
+#ifndef MY_DISPLAY_FGCOLOR
+#define MY_DISPLAY_FGCOLOR OLED_WHITE
+#endif
+#ifndef MY_DISPLAY_BGCOLOR
+#define MY_DISPLAY_BGCOLOR OLED_BLACK
+#endif
 
 // settings for TFT display library
 #elif (HAS_DISPLAY == 2)
@@ -42,6 +51,8 @@
 #define MY_FONT_LARGE 4
 #define MY_FONT_STRETCHED 6
 
+#define MY_DISPLAY_FIRSTLINE 30
+
 #ifndef MY_DISPLAY_FGCOLOR
 #define MY_DISPLAY_FGCOLOR TFT_WHITE
 #endif
@@ -76,7 +87,7 @@
 
 const uint8_t QR_SCALEFACTOR = (MY_DISPLAY_HEIGHT - 4) / 29; // 4px borderlines
 
-extern uint8_t DisplayIsOn, displaybuf[];
+extern uint8_t DisplayIsOn;
 extern hw_timer_t *displayIRQ;
 extern uint8_t volatile channel; // wifi channel rotation counter
 
@@ -86,11 +97,10 @@ void dp_init(bool verbose = false);
 void dp_shutdown(void);
 void dp_message(const char *msg, int line, bool invers);
 void dp_drawPage(bool nextpage);
-void dp_println(int lines = 1);
 void dp_printf(const char *format, ...);
 void dp_setFont(int font, int inv = 0);
-void dp_dump(uint8_t *pBuffer);
+void dp_dump(uint8_t *pBuffer = NULL);
-void dp_setTextCursor(int col, int row);
+void dp_setTextCursor(int col = 0, int row = MY_DISPLAY_FIRSTLINE);
 void dp_contrast(uint8_t contrast);
 void dp_clear(void);
 void dp_power(uint8_t screenon);

lib/BintrayClient/src/BintrayClient.cpp

@@ -21,6 +21,9 @@
 
 #include "BintrayClient.h"
 
+// Local logging tag
+static const char TAG[] = __FILE__;
+
 BintrayClient::BintrayClient(const String &user, const String &repository, const String &package)
     : m_user(user), m_repo(repository), m_package(package),
       m_storage_host("pax.express"),

platformio_orig.ini

@@ -14,10 +14,10 @@
 ;halfile = ttgov1.h
 ;halfile = ttgov2.h
 ;halfile = ttgov21old.h
-;halfile = ttgov21new.h
+halfile = ttgov21new.h
 ;halfile = ttgofox.h
 ;halfile = ttgobeam.h
-halfile = ttgobeam10.h
+;halfile = ttgobeam10.h
 ;halfile = ttgotdisplay.h
 ;halfile = ttgotwristband.h
 ;halfile = fipy.h
@@ -46,7 +46,7 @@ description = Paxcounter is a device for metering passenger flows in realtime. I
 
 [common]
 ; for release_version use max. 10 chars total, use any decimal format like "a.b.c"
-release_version = 3.2.1
+release_version = 3.3.0
 ; DEBUG LEVEL: For production run set to 0, otherwise device will leak RAM while running!
 ; 0=None, 1=Error, 2=Warn, 3=Info, 4=Debug, 5=Verbose
 debug_level = 3
@@ -54,14 +54,15 @@ extra_scripts = pre:build.py
 otakeyfile = ota.conf
 lorakeyfile = loraconf.h
 lmicconfigfile = lmic_config.h
-platform_espressif32 = espressif32@4.1.0
+platform_espressif32 = espressif32@5.0.0
 monitor_speed = 115200
 upload_speed = 115200 ; set by build.py and taken from hal file
 display_library = ; set by build.py and taken from hal file
 lib_deps_lora =
     mcci-catena/MCCI LoRaWAN LMIC library @ ^4.1.1
 lib_deps_display =
-    bitbank2/OneBitDisplay @ ^1.11.0
+    https://github.com/bitbank2/OneBitDisplay#8d4ab34
+    ;bitbank2/OneBitDisplay @ ^2.1.0
     ricmoo/QRCode @ ^0.0.1
     bodmer/TFT_eSPI @ ^2.3.84
 lib_deps_ledmatrix =

src/display.cpp

@@ -8,11 +8,11 @@ Display-Mask (128 x 64 pixel):
  |          11111111112
  |012345678901234567890   Font
 -----------------------   ---------
-0|PAX:aabbccdd      	    STRETCHED
+0|PAX:aabbccdd      	    LARGE
-1|PAX:aabbccdd            STRETCHED
+1|PAX:aabbccdd            LARGE
 2|
 3|WIFI:abcde BLTH:abcde   SMALL
-4|B:a.bcV Sats:ab ch:ab   SMALL
+4|Batt:abc%  chan:ab      SMALL
 5|RLIM:abcd  Mem:abcdKB   SMALL
 6|27.Feb 2019 20:27:00*   SMALL
 7|yyyyyyyyyyyyy xx SFab   SMALL
@@ -25,9 +25,10 @@ y = LMIC event message
 xx = payload sendqueue length
 ab = LMIC spread factor
 
-MY_FONT_SMALL:     6x8px = 21 chars / line
+MY_FONT_SMALL:     6x8px = 21 chars / line @ 8 lines
-MY_FONT_NORMAL:    8x8px = 16 chars / line
+MY_FONT_NORMAL:    8x8px = 16 chars / line @ 8 lines
-MY_FONT_STRETCHED: 16x32px = 8 chars / line
+MY_FONT_STRETCHED: 12x16px = 10 chars / line @ 4 lines
+MY_FONT_LARGE:     16x32px = 8 chars / line @ 2 lines
 
 */
 
@@ -39,18 +40,14 @@ MY_FONT_STRETCHED: 16x32px = 8 chars / line
 // local Tag for logging
 static const char TAG[] = __FILE__;
 
+static uint8_t plotbuf[PLOTBUFFERSIZE] = {0};
 uint8_t DisplayIsOn = 0;
-uint8_t displaybuf[MY_DISPLAY_WIDTH * MY_DISPLAY_HEIGHT / 8] = {0};
-static uint8_t plotbuf[MY_DISPLAY_WIDTH * MY_DISPLAY_HEIGHT / 8] = {0};
-static int dp_row = 0, dp_col = 0, dp_font = 0;
-
 hw_timer_t *displayIRQ = NULL;
-
 QRCode qrcode;
 
 #ifdef HAS_DISPLAY
 #if (HAS_DISPLAY) == 1
-OBDISP ssoled;
+ONE_BIT_DISPLAY oled;
 #elif (HAS_DISPLAY) == 2
 TFT_eSPI tft = TFT_eSPI(MY_DISPLAY_WIDTH, MY_DISPLAY_HEIGHT);
 #else
@@ -62,16 +59,11 @@ void dp_setup(int contrast) {
 
 #if (HAS_DISPLAY) == 1 // I2C OLED
 
-  int rc = obdI2CInit(&ssoled, OLED_TYPE, OLED_ADDR, MY_DISPLAY_FLIP,
+  oled.I2Cbegin(OLED_TYPE, OLED_ADDR, OLED_FREQUENCY);
-                      MY_DISPLAY_INVERT, USE_HW_I2C, MY_DISPLAY_SDA,
+  assert(oled.allocBuffer()); // render all outputs to lib internal backbuffer
-                      MY_DISPLAY_SCL, MY_DISPLAY_RST,
+  oled.setTextWrap(false);
-                      OLED_FREQUENCY); // use standard I2C bus at 400Khz
+  oled.setRotation(
-  _ASSERT(rc != OLED_NOT_FOUND);
+      MY_DISPLAY_FLIP ? 2 : 0); // 0 = no rotation, 1 = 90°, 2 = 180°, 3 = 280°
-
-  // set display buffer
-  obdSetBackBuffer(&ssoled, displaybuf);
-  obdSetTextWrap(&ssoled, true);
-  dp_font = MY_FONT_NORMAL;
 
 #elif (HAS_DISPLAY) == 2 // SPI TFT
 
@@ -103,22 +95,17 @@ void dp_init(bool verbose) {
     esp_chip_info(&chip_info);
 
     dp_setFont(MY_FONT_NORMAL);
-    dp_printf("** PAXCOUNTER **");
+    dp_printf("** PAXCOUNTER **\r\n");
-    dp_println();
+    dp_printf("Software v%s\r\n", PROGVERSION);
-    dp_printf("Software v%s", PROGVERSION);
+    dp_printf("ESP32 %d cores\r\n", chip_info.cores);
-    dp_println();
+    dp_printf("Chip Rev.%d\r\n", chip_info.revision);
-    dp_printf("ESP32 %d cores", chip_info.cores);
+    dp_printf("WiFi%s%s\r\n", (chip_info.features & CHIP_FEATURE_BT) ? "/BT" : "",
-    dp_println();
-    dp_printf("Chip Rev.%d", chip_info.revision);
-    dp_println();
-    dp_printf("WiFi%s%s", (chip_info.features & CHIP_FEATURE_BT) ? "/BT" : "",
               (chip_info.features & CHIP_FEATURE_BLE) ? "/BLE" : "");
-    dp_println();
     dp_printf("%dMB %s Flash", spi_flash_get_chip_size() / (1024 * 1024),
               (chip_info.features & CHIP_FEATURE_EMB_FLASH) ? "int." : "ext.");
 
     // give user some time to read or take picture
-    dp_dump(displaybuf);
+    dp_dump();
     delay(2000);
     dp_clear();
 #endif // VERBOSE
@@ -136,17 +123,16 @@ void dp_init(bool verbose) {
 
     // display DEVEUI as plain text on the right
     const int x_offset = QR_SCALEFACTOR * 29 + 14;
-    dp_setTextCursor(x_offset, 0);
     dp_setFont(MY_FONT_NORMAL);
-    dp_printf("DEVEUI");
+    dp_setTextCursor(x_offset, 0);
-    dp_println();
+    dp_printf("DEVEUI:\r\n");
     for (uint8_t i = 0; i <= 3; i++) {
-      dp_setTextCursor(x_offset, i + 3);
+      dp_setTextCursor(x_offset, i * 8 + 20);
       dp_printf("%4.4s", deveui + i * 4);
     }
 
     // give user some time to read or take picture
-    dp_dump(displaybuf);
+    dp_dump();
 #if !(BOOTMENU)
     delay(8000);
 #endif
@@ -198,10 +184,6 @@ void dp_drawPage(bool nextpage) {
   time_t now;
   struct tm timeinfo = {0};
 
-#if (HAS_GPS)
-  static bool wasnofix = true;
-#endif
-
   if (nextpage) {
     DisplayPage = (DisplayPage >= DISPLAY_PAGES - 1) ? 0 : (DisplayPage + 1);
     dp_clear();
@@ -215,9 +197,9 @@ void dp_drawPage(bool nextpage) {
 
   // line 1/2: pax counter
   // display number of unique macs total Wifi + BLE
-  if (DisplayPage < 5) {
+  if (DisplayPage < 3) {
-    dp_setFont(MY_FONT_STRETCHED);
+    dp_setFont(MY_FONT_LARGE);
-    dp_printf("%-5d", count.pax);
+    dp_printf("%-8d", count.pax);
   }
 
   switch (DisplayPage) {
@@ -233,8 +215,8 @@ void dp_drawPage(bool nextpage) {
     // ---------- page 0: parameters overview ----------
   case 0:
 
-    dp_setTextCursor(0, 3);
     dp_setFont(MY_FONT_SMALL);
+    dp_setTextCursor();
 
     // line 3: wifi + bluetooth counters
     // WIFI:abcde BLTH:abcde
@@ -260,7 +242,7 @@ void dp_drawPage(bool nextpage) {
 #else
     dp_printf("Sniffer disabled");
 #endif
-    dp_println();
+    dp_printf("\r\n");
 
     // line 4: Battery + GPS status + Wifi channel
     // B:a.bcV Sats:ab ch:ab
@@ -268,26 +250,16 @@ void dp_drawPage(bool nextpage) {
     if (batt_level == 0)
       dp_printf("No batt   ");
     else
-      dp_printf("B:%3d%%  ", batt_level);
+      dp_printf("Batt:%3u%% ", batt_level);
 #else
     dp_printf("          ");
 #endif
-
+    dp_printf("chan:%02u\r\n", channel);
-#if (HAS_GPS)
-    dp_setFont(MY_FONT_SMALL, !gps_hasfix());
-    dp_printf("Sats:%.2d", gps.satellites.value());
-    dp_setFont(MY_FONT_SMALL);
-#else
-    dp_printf("       ");
-#endif
-    dp_printf(" ch:%02d", channel);
-    dp_println();
 
     // line 5: RSSI limiter + free memory
     // RLIM:abcd  Mem:abcdKB
     dp_printf(!cfg.rssilimit ? "RLIM:off " : "RLIM:%-4d", cfg.rssilimit);
-    dp_printf("  Mem:%4dKB", getFreeRAM() / 1024);
+    dp_printf("  Mem:%4dKB\r\n", getFreeRAM() / 1024);
-    dp_println();
 
     // line 6: time + date
     // Wed Jan 12 21:49:08 *
@@ -302,12 +274,11 @@ void dp_drawPage(bool nextpage) {
 // display inverse timeState if clock controller is enabled
 #if (defined HAS_DCF77) || (defined HAS_IF482)
     dp_setFont(MY_FONT_SMALL, 1);
-    dp_printf("%c", timeState);
+    dp_printf("%c\r\n", timeState);
     dp_setFont(MY_FONT_SMALL, 0);
 #else
-    dp_printf("%c", timeState);
+    dp_printf("%c\r\n", timeState);
 #endif
-    dp_println();
 #endif // TIME_SYNC_INTERVAL
 
     // line 7: LMIC status
@@ -322,7 +293,7 @@ void dp_drawPage(bool nextpage) {
     dp_setFont(MY_FONT_SMALL, 0);
 #endif // HAS_LORA
 
-    dp_dump(displaybuf);
+    dp_dump();
     break;
 
   // ---------- page 1: lorawan parameters ----------
@@ -337,19 +308,15 @@ void dp_drawPage(bool nextpage) {
     // 7|SNR:-0000  RSSI:-0000
 
     dp_setFont(MY_FONT_SMALL);
-    dp_setTextCursor(0, 3);
+    dp_setTextCursor();
-    dp_printf("Net:%06X   Pwr:%-2d", LMIC.netid & 0x001FFFFF, LMIC.radio_txpow);
+    dp_printf("Net:%06X   Pwr:%-2d\r\n", LMIC.netid & 0x001FFFFF, LMIC.radio_txpow);
-    dp_println();
+    dp_printf("Dev:%08X DR:%1d\r\n", LMIC.devaddr, LMIC.datarate);
-    dp_printf("Dev:%08X DR:%1d", LMIC.devaddr, LMIC.datarate);
+    dp_printf("ChMsk:%04X Nonce:%04X\r\n", LMIC.channelMap, LMIC.devNonce);
-    dp_println();
+    dp_printf("fUp:%-6d fDn:%-6d\r\n", LMIC.seqnoUp ? LMIC.seqnoUp - 1 : 0,
-    dp_printf("ChMsk:%04X Nonce:%04X", LMIC.channelMap, LMIC.devNonce);
-    dp_println();
-    dp_printf("fUp:%-6d fDn:%-6d", LMIC.seqnoUp ? LMIC.seqnoUp - 1 : 0,
               LMIC.seqnoDn ? LMIC.seqnoDn - 1 : 0);
-    dp_println();
     dp_printf("SNR:%-5d  RSSI:%-5d", (LMIC.snr + 2) / 4, LMIC.rssi);
 
-    dp_dump(displaybuf);
+    dp_dump();
     break;
 #else  // flip page if we are unattended
     DisplayPage++;
@@ -359,31 +326,21 @@ void dp_drawPage(bool nextpage) {
   case 2:
 
 #if (HAS_GPS)
+
+    // show satellite status at bottom line
+    dp_setFont(MY_FONT_SMALL);
+    dp_setTextCursor(0, 56);
+    dp_printf("%u Sats", gps.satellites.value());
+    dp_printf(gps_hasfix() ? "         " : " - No fix");
+
+    // show latitude and longitude
     dp_setFont(MY_FONT_STRETCHED);
-    dp_setTextCursor(0, 3);
+    dp_setTextCursor();
-    if (gps_hasfix()) {
+    dp_printf("%c%09.6f\r\n", gps.location.rawLat().negative ? 'S' : 'N',
-      // line 5: clear "No fix"
-      if (wasnofix) {
-        dp_setTextCursor(2, 4);
-        dp_printf("      ");
-        wasnofix = false;
-      }
-      // line 3-4: GPS latitude
-      dp_printf("%c%07.4f", gps.location.rawLat().negative ? 'S' : 'N',
               gps.location.lat());
-
+    dp_printf("%c%09.6f", gps.location.rawLng().negative ? 'W' : 'E',
-      // line 6-7: GPS longitude
-      dp_printf("%c%07.4f", gps.location.rawLng().negative ? 'W' : 'E',
               gps.location.lng());
-
+    dp_dump();
-    } else {
-      dp_setTextCursor(2, 4);
-      dp_setFont(MY_FONT_STRETCHED, 1);
-      dp_printf("No fix");
-      wasnofix = true;
-    }
-
-    dp_dump(displaybuf);
     break;
 #else // flip page if we are unattended
     DisplayPage++;
@@ -394,25 +351,14 @@ void dp_drawPage(bool nextpage) {
 
 #if (HAS_BME)
     dp_setFont(MY_FONT_STRETCHED);
-    dp_setTextCursor(0, 2);
+    dp_setTextCursor(0, 0);
-
+    dp_printf("TMP: %-6.1f\r\n", bme_status.temperature);
-    // line 2-3: Temp
+    dp_printf("HUM: %-6.1f\r\n", bme_status.humidity);
-    dp_printf("TMP:%-2.1f", bme_status.temperature);
+    dp_printf("PRE: %-6.1f\r\n", bme_status.pressure);
-    dp_println(2);
-
-    // line 4-5: Hum
-    dp_printf("HUM:%-2.1f", bme_status.humidity);
-    dp_println(2);
-
 #ifdef HAS_BME680
-    // line 6-7: IAQ
+    dp_printf("IAQ: %-6.0f", bme_status.iaq);
-    dp_printf("IAQ:%-3.0f", bme_status.iaq);
+#endif
-#else  // is BME280 or BMP180
+    dp_dump();
-    // line 6-7: Pre
-    dp_printf("PRE:%-2.1f", bme_status.pressure);
-#endif // HAS_BME680
-
-    dp_dump(displaybuf);
     break; // page 3
 #else      // flip page if we are unattended
     DisplayPage++;
@@ -421,20 +367,25 @@ void dp_drawPage(bool nextpage) {
   // ---------- page 4: time ----------
   case 4:
 
-    dp_setFont(MY_FONT_LARGE);
-    dp_setTextCursor(0, 4);
     time(&now);
     localtime_r(&now, &timeinfo);
     strftime(strftime_buf, sizeof(strftime_buf), "%T", &timeinfo);
-    dp_printf("%.8s", strftime_buf);
 
-    dp_dump(displaybuf);
+    dp_setFont(MY_FONT_STRETCHED);
+    dp_setTextCursor(0, 0);
+    dp_printf("Timeofday:");
+    dp_setTextCursor(0, 26);
+    dp_setFont(MY_FONT_LARGE);
+    dp_printf("%.8s\r\n", strftime_buf);
+    dp_setFont(MY_FONT_SMALL);
+    dp_printf("%21.1f", uptime() / 1000.0);
+    dp_dump();
     break;
 
   // ---------- page 5: pax graph ----------
   case 5:
 
-    // update histogram
+    // update and show histogram
     dp_plotCurve(count.pax, false);
     dp_dump(plotbuf);
     break;
@@ -455,35 +406,33 @@ void dp_drawPage(bool nextpage) {
 // ------------- display helper functions -----------------
 
 void dp_setTextCursor(int x, int y) {
-  // x represents the pixel column
-  // y represents the text row
-  dp_col = x;
-
 #if (HAS_DISPLAY) == 1
-  dp_row = y;
+  oled.setCursor(x, y);
-  obdSetCursor(&ssoled, dp_col, dp_row);
-
 #elif (HAS_DISPLAY) == 2
-  switch (dp_font >> 1) {
+  tft.setCursor(x, y);
-  case MY_FONT_STRETCHED:
-  case MY_FONT_LARGE:
-    dp_row = y * 26;
-    break;
-  case MY_FONT_SMALL:
-  case MY_FONT_NORMAL:
-  default:
-    dp_row = y * 16;
-    break;
-  }
-  tft.setCursor(dp_col, dp_row);
 #endif
 }
 
 void dp_setFont(int font, int inv) {
+
 #if (HAS_DISPLAY) == 1
-  dp_font = (font << 1) | (inv & 0x01);
+  // handle invers printing
+  if (inv)
+    oled.setTextColor(MY_DISPLAY_BGCOLOR, MY_DISPLAY_FGCOLOR);
+  else
+    oled.setTextColor(MY_DISPLAY_FGCOLOR, MY_DISPLAY_BGCOLOR);
+
+  // set desired font
+  oled.setFont(font);
+
 #elif (HAS_DISPLAY) == 2
-  // map font oled -> tft
+  // handle invers printing
+  if (inv)
+    tft.setTextColor(MY_DISPLAY_BGCOLOR, MY_DISPLAY_FGCOLOR);
+  else
+    tft.setTextColor(MY_DISPLAY_FGCOLOR, MY_DISPLAY_BGCOLOR);
+
+  // map desired oled font to tft font
   switch (font) {
   case MY_FONT_STRETCHED: // 16x16 on OLED
   case MY_FONT_LARGE:     // 16x32 on OLED
@@ -495,21 +444,10 @@ void dp_setFont(int font, int inv) {
     tft.setTextFont(2); // 16px
     break;
   }
-  // to do: invers printing
+  
 #endif
 }
 
-void dp_println(int lines) {
-  dp_col = 0;
-  dp_row += lines;
-#if (HAS_DISPLAY) == 1
-  dp_setTextCursor(dp_col, dp_row);
-#elif (HAS_DISPLAY) == 2
-  for (int i = 1; i <= lines; i++)
-    tft.println();
-#endif
-};
-
 void dp_printf(const char *format, ...) {
   char loc_buf[64];
   char *temp = loc_buf;
@@ -533,8 +471,7 @@ void dp_printf(const char *format, ...) {
   }
   va_end(arg);
 #if (HAS_DISPLAY) == 1
-  obdWriteString(&ssoled, 0, -1, dp_row, temp, dp_font >> 1, dp_font & 0x01,
+  oled.write(temp);
-                 false);
 #elif (HAS_DISPLAY) == 2
   tft.printf(temp);
 #endif
@@ -545,26 +482,29 @@ void dp_printf(const char *format, ...) {
 
 void dp_dump(uint8_t *pBuffer) {
 #if (HAS_DISPLAY) == 1
-  obdDumpBuffer(&ssoled, pBuffer);
+  if (pBuffer)
+    memcpy(oled.getBuffer(), pBuffer, PLOTBUFFERSIZE);
+  oled.display();
 #elif (HAS_DISPLAY) == 2
-  // probably oled buffer stucture is not suitable for tft -> to be checked
+  if (pBuffer)
     tft.drawBitmap(0, 0, pBuffer, MY_DISPLAY_WIDTH, MY_DISPLAY_HEIGHT,
                    MY_DISPLAY_FGCOLOR);
 #endif
 }
 
 void dp_clear(void) {
-  dp_setTextCursor(0, 0);
 #if (HAS_DISPLAY) == 1
-  obdFill(&ssoled, 0, 1);
+  oled.fillScreen(MY_DISPLAY_BGCOLOR);
+  oled.display();
 #elif (HAS_DISPLAY) == 2
   tft.fillScreen(MY_DISPLAY_BGCOLOR);
 #endif
+  dp_setTextCursor(0, 0);
 }
 
 void dp_contrast(uint8_t contrast) {
 #if (HAS_DISPLAY) == 1
-  obdSetContrast(&ssoled, contrast);
+  oled.setContrast(contrast);
 #elif (HAS_DISPLAY) == 2
   // to do: gamma correction for TFT
 #endif
@@ -572,7 +512,7 @@ void dp_contrast(uint8_t contrast) {
 
 void dp_power(uint8_t screenon) {
 #if (HAS_DISPLAY) == 1
-  obdPower(&ssoled, screenon);
+  oled.setPower(screenon);
 #elif (HAS_DISPLAY) == 2
   // to come
 #endif
@@ -580,7 +520,7 @@ void dp_power(uint8_t screenon) {
 
 void dp_shutdown(void) {
 #if (HAS_DISPLAY) == 1
-  obdPower(&ssoled, false);
+  oled.setPower(false);
   delay(DISPLAYREFRESH_MS / 1000 * 1.1);
 #elif (HAS_DISPLAY) == 2
   // to come
@@ -589,10 +529,10 @@ void dp_shutdown(void) {
 
 // print static message on display
 void dp_message(const char *msg, int line, bool invers) {
-  dp_setTextCursor(0, line);
+  dp_setFont(MY_FONT_SMALL, invers ? 1 : 0);
-  dp_setFont(MY_FONT_NORMAL, invers ? 1 : 0);
+  dp_setTextCursor(0, line * 8);
   dp_printf("%-16s", msg);
-  dp_dump(displaybuf);
+  dp_dump();
 } // dp_message
 
 // ------------- QR code plotter -----------------
@@ -625,8 +565,7 @@ void dp_printqr(uint16_t offset_x, uint16_t offset_y, const char *Message) {
 void dp_fillRect(uint16_t x, uint16_t y, uint16_t width, uint16_t height,
                  uint8_t bRender) {
 #if (HAS_DISPLAY) == 1
-  for (uint16_t xi = x; xi < x + width; xi++)
+  oled.fillRect(x, y, width, height, MY_DISPLAY_FGCOLOR);
-    obdDrawLine(&ssoled, xi, y, xi, y + height - 1, 1, bRender);
 #elif (HAS_DISPLAY) == 2
   tft.fillRect(x, y, width, height, MY_DISPLAY_FGCOLOR);
 #endif

src/hal/m5fire.h

@@ -29,7 +29,6 @@
 #define SDCARD_SCLK  SCK
 
 #define CFG_sx1276_radio 1 // select LoRa chip
-#define BOARD_HAS_PSRAM // use if board has external PSRAM
 #define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
 
 #define HAS_DISPLAY 2 // TFT-LCD, support work in progess, not ready yet

src/i2c.cpp

@@ -38,14 +38,6 @@ void i2c_scan(void) {
 
   BBI2C bbi2c;
 
-  const char *szNames[] = {
-      "Unknown",    "SSD1306",  "SH1106",   "VL53L0X", "BMP180",  "BMP280",
-      "BME280",     "MPU-60x0", "MPU-9250", "MCP9808", "LSM6DS3", "ADXL345",
-      "ADS1115",    "MAX44009", "MAG3110",  "CCS811",  "HTS221",  "LPS25H",
-      "LSM9DS1",    "LM8330",   "DS3231",   "LIS3DH",  "LIS3DSH", "INA219",
-      "SHT3X",      "HDC1080",  "MPU6886",  "BME680",  "AXP202",  "AXP192",
-      "24AA02XEXX", "DS1307"};
-
   ESP_LOGI(TAG, "Starting I2C bus scan...");
 
   memset(&bbi2c, 0, sizeof(bbi2c));
@@ -58,6 +50,8 @@ void i2c_scan(void) {
   uint8_t map[16];
   uint8_t i;
   int iDevice, iCount;
+  uint32_t iDevCapab;
+  char szName[15];
 
   I2CScan(&bbi2c, map); // get bitmap of connected I2C devices
   if (map[0] == 0xfe)   // something is wrong with the I2C bus
@@ -72,9 +66,10 @@ void i2c_scan(void) {
       if (map[i >> 3] & (1 << (i & 7))) // device found
       {
         iCount++;
-        iDevice = I2CDiscoverDevice(&bbi2c, i);
+        iDevice = I2CDiscoverDevice(&bbi2c, i, &iDevCapab);
+        I2CGetDeviceName(iDevice, szName);
         ESP_LOGI(TAG, "Device found at 0x%X, type = %s", i,
-                 szNames[iDevice]); // show the device name as a string
+                 szName); // show the device name as a string
       }
     } // for i
     ESP_LOGI(TAG, "%u I2C device(s) found", iCount);

src/ota.cpp

@@ -50,19 +50,14 @@ void start_ota_update() {
 #ifdef HAS_DISPLAY
 
   dp_setup();
-
+  dp_setFont(MY_FONT_NORMAL);
-  dp_printf("SOFTWARE UPDATE");
+  dp_printf("SOFTWARE UPDATE\r\n");
-  dp_println();
+  dp_printf("WiFi connect  ..\r\n");
-  dp_printf("WiFi connect  ..");
+  dp_printf("Has Update?   ..\r\n");
-  dp_println();
+  dp_printf("Fetching      ..\r\n");
-  dp_printf("Has Update?   ..");
+  dp_printf("Downloading   ..\r\n");
-  dp_println();
+  dp_printf("Rebooting     ..\r\n");
-  dp_printf("Fetching      ..");
+  dp_dump();
-  dp_println();
-  dp_printf("Downloading   ..");
-  dp_println();
-  dp_printf("Rebooting     ..");
-  dp_dump(displaybuf);
 #endif
 
   ESP_LOGI(TAG, "Starting Wifi OTA update");
@@ -330,15 +325,14 @@ retry:
 void ota_display(const uint8_t row, const std::string status,
                  const std::string msg) {
 #ifdef HAS_DISPLAY
-  dp_setFont(MY_FONT_SMALL);
+  dp_setTextCursor(14 * 8, row * 8);
-  dp_setTextCursor(14, row);
   dp_printf(status.substr(0, 2).c_str());
   if (!msg.empty()) {
     dp_printf("                ");
     dp_printf(msg.substr(0, 16).c_str());
-    dp_println();
+    // dp_printf("\r\n");
   }
-  dp_dump(displaybuf);
+  dp_dump();
 #endif
 }
 

src/power.cpp

@@ -64,10 +64,12 @@ void AXP192_powerevent_IRQ(void) {
     pmu.setChgLEDMode(AXP20X_LED_BLINK_1HZ);
   }
 
+#ifdef HAS_BUTTON
   // short press -> esp32 deep sleep mode, can be exited by pressing user button
   if (pmu.isPEKShortPressIRQ()) {
     enter_deepsleep(0, HAS_BUTTON);
   }
+#endif
 
   // long press -> shutdown power, can be exited by another longpress
   if (pmu.isPEKLongtPressIRQ()) {

src/reset.cpp

@@ -200,9 +200,9 @@ void enter_deepsleep(const uint64_t wakeup_sec, gpio_num_t wakeup_gpio) {
 
   // time stamp sleep start time and save system monotonic time. Deep sleep.
   gettimeofday(&RTC_sleep_start_time, NULL);
-  RTC_millis += millis();
+  RTC_millis += esp_timer_get_time() / 1000;
   ESP_LOGI(TAG, "Going to sleep, good bye.");
   esp_deep_sleep_start();
 }
 
-unsigned long long uptime() { return (RTC_millis + millis()); }
+unsigned long long uptime() { return (RTC_millis + esp_timer_get_time() / 1000); }