diff --git a/src/paxcounter.conf b/src/paxcounter.conf deleted file mode 100644 index e82d6adb..00000000 --- a/src/paxcounter.conf +++ /dev/null @@ -1,122 +0,0 @@ -// clang-format off - -// ----- Paxcounter user config file ------ -// -// --> adapt to your needs and use case <-- -// -// Note: After editing, before "build", use "clean" button in PlatformIO! - -// Verbose enables additional serial debug output -#define VERBOSE 1 // set to 0 to silence the device, for mute use build option - -// Payload send cycle and encoding -#define SENDCYCLE 30 // payload send cycle [seconds/2], 0 .. 255 -#define PAYLOAD_ENCODER 2 // payload encoder: 1=Plain, 2=Packed, 3=Cayenne LPP dynamic, 4=Cayenne LPP packed -#define COUNTERMODE 1 // 0=cyclic, 1=cumulative, 2=cyclic confirmed - -// Set this to include BLE counting and vendor filter functions, or to switch off WIFI counting -#define VENDORFILTER 0 // set to 0 if you want to scan all devices, not filtering smartphone OUIs -#define BLECOUNTER 1 // set to 0 if you do not want to install the BLE sniffer -#define WIFICOUNTER 1 // set to 0 if you do not want to install the WIFI sniffer - -// BLE scan parameters -#define BLESCANTIME 0 // [seconds] scan duration, 0 means infinite [default], see note below -#define BLESCANWINDOW 80 // [milliseconds] scan window, see below, 3 .. 10240, default 80ms -#define BLESCANINTERVAL 80 // [illiseconds] scan interval, see below, 3 .. 10240, default 80ms = 100% duty cycle - -// Corona Exposure Notification Service(ENS) counter -#define COUNT_ENS 1 // count found number of devices which advertise Exposure Notification Service - // set to 0 if you do not want to enable this function - -// for additional sensors (added by some user) -#define HAS_SENSOR_1 1 // set to 1 if you want to transmit CWA counter -#define HAS_SENSOR_2 0 // not used -#define HAS_SENSOR_3 0 // not used -#define HAS_SENSORS (HAS_SENSOR_1 || HAS_SENSOR_2 || HAS_SENSOR_3) // to simplify things - -/* Note: guide for setting bluetooth parameters -* -* |< Scan Window > |< Scan Window > | ... |< Scan Window > | -* |< Scan Interval >|< Scan Interval >| ... |< Scan Interval >| -* |< Scan duration >| -* -* Scan duration sets how long scanning should be going on, before starting a new scan cycle. 0 means infinite (default). -* Scan window sets how much of the interval should be occupied by scanning. Should be >= BLESCANINTERVAL. -* Scan interval is how long scanning should be done on each channel. BLE uses 3 channels for advertising. -* -> Adjust these values with power consumption in mind if power is limited. -* -> Scan interval can be changed during runtime by remote comammand. -*/ - -// WiFi scan parameters -#define WIFI_CHANNEL_MIN 1 // start channel number where scan begings -#define WIFI_CHANNEL_MAX 13 // total channel number to scan -#define WIFI_MY_COUNTRY "EU" // select locale for Wifi RF settings -#define WIFI_CHANNEL_SWITCH_INTERVAL 50 // [seconds/100] -> 0,5 sec. - -// LoRa payload default parameters -#define MEM_LOW 2048 // [Bytes] low memory threshold triggering a send cycle -#define RETRANSMIT_RCMD 5 // [seconds] wait time before retransmitting rcommand results -#define PAYLOAD_BUFFER_SIZE 51 // maximum size of payload block per transmit -#define PAYLOAD_OPENSENSEBOX 0 // send payload compatible to sensebox.de (swap geo position and pax data) -#define LORADRDEFAULT 5 // 0 .. 15, LoRaWAN datarate, according to regional LoRaWAN specs [default = 5] -#define LORATXPOWDEFAULT 14 // 0 .. 255, LoRaWAN TX power in dBm [default = 14] -#define MAXLORARETRY 500 // maximum count of TX retries if LoRa busy -#define SEND_QUEUE_SIZE 10 // maximum number of messages in payload send queue [1 = no queue] - -// Hardware settings -#define RGBLUMINOSITY 30 // RGB LED luminosity [default = 30%] -#define DISPLAYREFRESH_MS 40 // OLED refresh cycle in ms [default = 40] -> 1000/40 = 25 frames per second -#define DISPLAYCONTRAST 80 // 0 .. 255, OLED display contrast [default = 80] -#define DISPLAYCYCLE 3 // Auto page flip delay in sec [default = 2] for devices without button -#define HOMECYCLE 30 // house keeping cycle in seconds [default = 30 secs] - -// Settings for BME680 environmental sensor -#define BME_TEMP_OFFSET 5.0f // Offset sensor on chip temp <-> ambient temp [default = 5°C] -#define STATE_SAVE_PERIOD UINT32_C(360 * 60 * 1000) // update every 360 minutes = 4 times a day -#define BMECYCLE 1 // bme sensor read cycle in seconds [default = 1 secs] - -// OTA settings -#define USE_OTA 1 // set to 0 to disable OTA update -#define WIFI_MAX_TRY 5 // maximum number of wifi connect attempts for OTA update [default = 20] -#define OTA_MAX_TRY 5 // maximum number of attempts for OTA download and write to flash [default = 3] -#define OTA_MIN_BATT 50 // minimum battery level for OTA [percent] -#define RESPONSE_TIMEOUT_MS 60000 // firmware binary server connection timeout [milliseconds] - -// settings for syncing time of node with a time source (network / gps / rtc / timeserver) -#define TIME_SYNC_LORAWAN 1 // set to 1 to use LORA network as time source, 0 means off [default = 1] -#define TIME_SYNC_LORASERVER 0 // set to 1 to use LORA timeserver as time source, 0 means off [default = 0] -#define TIME_SYNC_INTERVAL 60 // sync time attempt each .. minutes from time source [default = 60], 0 means off -#define TIME_SYNC_INTERVAL_RETRY 10 // retry time sync after lost sync each .. minutes [default = 10], 0 means off -#define TIME_SYNC_SAMPLES 1 // number of time requests for averaging, max. 255 -#define TIME_SYNC_CYCLE 60 // delay between two time samples [seconds] -#define TIME_SYNC_TIMEOUT 400 // timeout waiting for timeserver answer [seconds] -#define TIME_SYNC_COMPILEDATE 0 // set to 1 to use compile date to initialize RTC after power outage [default = 0] - -// time zone, see https://github.com/JChristensen/Timezone/blob/master/examples/WorldClock/WorldClock.ino -#define DAYLIGHT_TIME {"CEST", Last, Sun, Mar, 2, 120} // Central European Summer Time -#define STANDARD_TIME {"CET ", Last, Sun, Oct, 3, 60} // Central European Standard Time - -// Ports on which the device sends and listenes on LoRaWAN and SPI -#define COUNTERPORT 1 // counts -#define MACPORT 0 // network commands -#define RCMDPORT 2 // remote commands -#define STATUSPORT 2 // remote command results -#define CONFIGPORT 3 // config query results -#define GPSPORT 4 // gps - NOTE: set to 1 to send combined GPS+COUNTERPORT payload -#define BUTTONPORT 5 // button pressed signal -#define BEACONPORT 6 // beacon alarms -#define BMEPORT 7 // BME680 sensor -#define BATTPORT 8 // battery voltage -#define TIMEPORT 9 // time query and response -#define SENSOR1PORT 10 // user sensor #1 -#define SENSOR2PORT 11 // user sensor #2 -#define SENSOR3PORT 12 // user sensor #3 - -// Cayenne LPP Ports, see https://community.mydevices.com/t/cayenne-lpp-2-0/7510 -#define CAYENNE_LPP1 1 // dynamic sensor payload (LPP 1.0) -#define CAYENNE_LPP2 2 // packed sensor payload (LPP 2.0) -#define CAYENNE_GPS 3 // full scale GPS payload -#define CAYENNE_ACTUATOR 10 // actuator commands -#define CAYENNE_DEVICECONFIG 11 // device period configuration -#define CAYENNE_SENSORREAD 13 // sensor period configuration -#define CAYENNE_SENSORENABLE 14 // sensor enable configuration