improve sd-card MMC handling

include/sdcard.h

@@ -11,17 +11,8 @@
 
 #define MOUNT_POINT "/sdcard"
 
-#if HAS_SDCARD == 1
+#if HAS_SDCARD == 1 // SPI interface
 #include "driver/sdspi_host.h"
-#elif HAS_SDCARD == 2
-#include "driver/sdmmc_host.h"
-#else
-#error HAS_SDCARD unknown card reader value, must be either 1 or 2
-#endif
-
-#ifdef HAS_SDS011
-#include "sds011read.h"
-#endif
 
 #ifndef SDCARD_CS
 #define SDCARD_CS SS
@@ -39,6 +30,25 @@
 #define SDCARD_SCLK SCK
 #endif
 
+#elif HAS_SDCARD == 2 // MMC interface
+#include "driver/sdmmc_host.h"
+
+#ifndef SDCARD_SLOTWIDTH
+#define SDCARD_SLOTWIDTH 1
+#endif
+
+#ifndef SDCARD_PULLUP
+#define SDCARD_PULLUP SDMMC_SLOT_FLAG_INTERNAL_PULLUP
+#endif
+
+#else
+#error HAS_SDCARD unknown card reader value, must be either 1 or 2
+#endif
+
+#ifdef HAS_SDS011
+#include "sds011read.h"
+#endif
+
 #define SDCARD_FILE_NAME clientId
 #define SDCARD_FILE_HEADER "timestamp,wifi,ble"
 

src/hal/ttgov21new.h

@@ -9,14 +9,15 @@
 
 /*  Hardware related definitions for TTGO V2.1 Board
 // ATTENTION: check your board version!
-// This settings are for boards labeled v1.6 on pcb, NOT for v1.5 or older
+// This settings are for boards labeled v1.6 or v1.6.1 on pcb, NOT for v1.5 or older
 */
 
 #define HAS_LORA         1 // comment out if device shall not send data via LoRa
 #define CFG_sx1276_radio 1 // HPD13A LoRa SoC
 
 // enable only if you want to store a local paxcount table on the device
-#define HAS_SDCARD  2      // this board has a SDMMC card-reader/writer
+#define HAS_SDCARD  2      // this board has a SD MMC card-reader/writer
+#define SDCARD_SLOTWIDTH 4 // 4-line interface
 
 #define HAS_DISPLAY 1
 #define HAS_LED (25) // green on board LED

src/sdcard.cpp

@@ -140,13 +140,13 @@ bool sdcard_init(bool create) {
   // https://docs.espressif.com/projects/esp-idf/en/latest/esp32/api-reference/peripherals/sdmmc_host.html
   sdmmc_slot_config_t slot_config = SDMMC_SLOT_CONFIG_DEFAULT();
 
-  // To use 4-line SD mode, change this to 4:
+  // Set 1-line or 4-line SD mode (default is 1-line)
-  slot_config.width = 1;
+  slot_config.width = SDCARD_SLOTWIDTH;
 
   // Enable internal pullups on enabled pins. The internal pullups
   // are insufficient however, please make sure 10k external pullups are
   // connected on the bus. This is for debug / example purpose only.
-  slot_config.flags |= SDMMC_SLOT_FLAG_INTERNAL_PULLUP;
+  slot_config.flags |= SDCARD_PULLUP;
 
   // Use settings defined above to initialize SD card and mount FAT filesystem.
   esp_err_t ret = esp_vfs_fat_sdmmc_mount(mount_point, &host, &slot_config,
@@ -180,7 +180,7 @@ bool sdcard_init(bool create) {
     fgetpos(data_file, &position);
 
     // empty file? then we write a header line
-    if (position = 0) {
+    if (position == 0) {
       fprintf(data_file, "%s", SDCARD_FILE_HEADER);
 #if (defined BAT_MEASURE_ADC || defined HAS_PMU)
       fprintf(data_file, "%s", SDCARD_FILE_HEADER_VOLTAGE);
@@ -188,8 +188,8 @@ bool sdcard_init(bool create) {
 #if (HAS_SDS011)
       fprintf(data_file, "%s", SDCARD_FILE_HEADER_SDS011);
 #endif
-      fprintf(data_file, "\n");
     }
+    fprintf(data_file, "\n");
 
   } else {
     useSDCard = false;