v1.7.11

platformio.ini

@@ -15,8 +15,7 @@ env_default = generic
 ;env_default = ttgov2
 ;env_default = ttgov21old
 ;env_default = ttgov21new
-;env_default = ttgobeam_old
+;env_default = ttgobeam
-;env_default = ttgobeam_new
 ;env_default = lopy
 ;env_default = lopy4
 ;env_default = fipy
@@ -30,7 +29,7 @@ description = Paxcounter is a proof-of-concept ESP32 device for metering passeng
 
 [common]
 ; for release_version use max. 10 chars total, use any decimal format like "a.b.c"
-release_version = 1.7.08
+release_version = 1.7.11
 ; DEBUG LEVEL: For production run set to 0, otherwise device will leak RAM while running!
 ; 0=None, 1=Error, 2=Warn, 3=Info, 4=Debug, 5=Verbose
 debug_level = 0
@@ -39,8 +38,8 @@ upload_protocol = esptool
 ;upload_protocol = custom
 extra_scripts = pre:build.py
 keyfile = ota.conf
-;platform_espressif32 = espressif32@1.5.0
+platform_espressif32 = espressif32@1.6.0
-platform_espressif32 = https://github.com/platformio/platform-espressif32.git#feature/stage
+;platform_espressif32 = https://github.com/platformio/platform-espressif32.git#feature/stage
 board_build.partitions = min_spiffs.csv
 monitor_speed = 115200
 lib_deps_lora = 
@@ -63,7 +62,7 @@ lib_deps_all =
 build_flags_basic =
     -include "src/hal/${PIOENV}.h"
     -include "src/paxcounter.conf"
- ;   -w
+    -w
     '-DARDUINO_LMIC_PROJECT_CONFIG_H=../../../src/lmic_config.h'
     '-DCORE_DEBUG_LEVEL=${common.debug_level}'
     '-DLOG_LOCAL_LEVEL=${common.debug_level}'
@@ -203,17 +202,17 @@ upload_protocol = ${common.upload_protocol}
 extra_scripts = ${common.extra_scripts}
 monitor_speed = ${common.monitor_speed}
 
-[env:ttgobeam_old]
+[env:ttgobeam]
 platform = ${common.platform_espressif32}
 framework = arduino
-board = esp32dev
+board = ttgo-t-beam
-;board = ttgo-t-beam
 board_build.partitions = ${common.board_build.partitions}
 upload_speed = 921600
 lib_deps = 
     ${common.lib_deps_basic}
     ${common.lib_deps_lora}
     ${common.lib_deps_gps}
+;   ${common.lib_deps_display}
 build_flags = 
     ${common.build_flags_all}
     -mfix-esp32-psram-cache-issue
@@ -221,25 +220,6 @@ upload_protocol = ${common.upload_protocol}
 extra_scripts = ${common.extra_scripts}
 monitor_speed = ${common.monitor_speed}
 
-[env:ttgobeam_new]
-platform = ${common.platform_espressif32}
-framework = arduino
-board = esp32dev
-;board = ttgo-t-beam
-board_build.partitions = ${common.board_build.partitions}
-upload_speed = 921600
-lib_deps = 
-    ${common.lib_deps_basic}
-    ${common.lib_deps_lora}
-    ${common.lib_deps_gps}
-build_flags = 
-    ${common.build_flags_all}
-    -mfix-esp32-psram-cache-issue
-upload_protocol = ${common.upload_protocol}
-extra_scripts = ${common.extra_scripts}
-monitor_speed = ${common.monitor_speed}
-
-
 [env:fipy]
 platform = ${common.platform_espressif32}
 framework = arduino

src/hal/ttgobeam.h

@@ -6,46 +6,37 @@
 #include <stdint.h>
 
 // Hardware related definitions for TTGO T-Beam board
+// (only) for older T-Beam version T22_V05 eternal wiring LORA_IO1 to GPIO33 is needed!
 //
 // pinouts taken from http://tinymicros.com/wiki/TTGO_T-Beam
 
+#define HAS_LED GPIO_NUM_14 // on board green LED, only new version TTGO-BEAM V07
+//#define HAS_LED GPIO_NUM_21 // on board green LED, only old verison TTGO-BEAM V05
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+#define BOARD_HAS_PSRAM // use extra 4MB external RAM
+#define HAS_BUTTON GPIO_NUM_39 // on board button (next to reset)
+#define HAS_BATTERY_PROBE ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BATT_FACTOR 2 // voltage divider 100k/100k on board
+#define HAS_GPS 1 // use on board GPS
+#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M or 7M with default configuration
+
 // enable only if device has these sensors, otherwise comment these lines
 // BME680 sensor on I2C bus
 //#define HAS_BME GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
 //#define BME_ADDR BME680_I2C_ADDR_PRIMARY // connect SDIO of BME680 to GND
 
-#define HAS_LED GPIO_NUM_14 // on board green LED
+// display (if connected)
-
-// user defined sensors
-//#define HAS_SENSORS 1 // comment out if device has user defined sensors
-
 //#define HAS_DISPLAY U8X8_SSD1306_128X64_NONAME_HW_I2C
 //#define MY_OLED_SDA (21)
 //#define MY_OLED_SCL (22)
 //#define MY_OLED_RST U8X8_PIN_NONE
 //#define DISPLAY_FLIP  1 // use if display is rotated
 
-#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+// user defined sensors (if connected)
-#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+//#define HAS_SENSORS 1 // comment out if device has user defined sensors
-#define BOARD_HAS_PSRAM // use extra 4MB external RAM
 
 //#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
 
-#define HAS_BUTTON GPIO_NUM_39 // on board button "SW5"
-
-#define HAS_BATTERY_PROBE ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
-#define BATT_FACTOR 2 // voltage divider 100k/100k on board
-#define HAS_GPS 1 // use on board GPS
-#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M or 7M with default configuration
-
-// Pins for LORA chip SPI interface, reset line and interrupt lines
-#define LORA_SCK  (5) 
-#define LORA_CS   (18)
-#define LORA_MISO (19)
-#define LORA_MOSI (27)
-#define LORA_RST  (23)
-#define LORA_IRQ  (26)
-#define LORA_IO1  (33)  // for T-Beam T22_V05 and T22_V07, for other versions use ttgobeam_old.h
-#define LORA_IO2  (32)
-
 #endif

src/hal/ttgobeam_old.h

@@ -9,11 +9,11 @@
 
 // enable only if device has these sensors, otherwise comment these lines
 // BME680 sensor on I2C bus
-//#define HAS_BME GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
+#define HAS_BME GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
-//#define BME_ADDR BME680_I2C_ADDR_PRIMARY // connect SDIO of BME680 to GND
+#define BME_ADDR BME680_I2C_ADDR_PRIMARY // connect SDIO of BME680 to GND
-//#define HAS_LED NOT_A_PIN // on board green LED uses same GPIO as SDA!
+#define HAS_LED NOT_A_PIN // on board green LED uses same GPIO as SDA!
 
-#define HAS_LED GPIO_NUM_21 // on board green LED
+// #define HAS_LED GPIO_NUM_21 // on board green LED
 
 // user defined sensors
 //#define HAS_SENSORS 1 // comment out if device has user defined sensors