move hal files from /src to /shared

shared/build.py

@@ -23,7 +23,8 @@ config.read("platformio.ini")
 srcdir = env.get("PROJECT_SRC_DIR")
 
 # get hal path
-haldir = os.path.join (srcdir, "hal")
+prjdir = env.get("PROJECT_DIR")
+haldir = os.path.join (prjdir, "shared/hal")
 
 # check if hal file is present in source directory
 halconfig = config.get("board", "halfile")

shared/hal/ebox.h

@@ -0,0 +1,29 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+#ifndef _EBOX_H
+#define _EBOX_H
+
+#include <stdint.h>
+
+// Hardware related definitions for ebox ESP32-bit with external connected RFM95 LoRa
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1
+
+#define HAS_LED (23) // blue LED on board
+#define HAS_BUTTON (0) // button "PROG" on board
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (18)
+#define LORA_MISO (19)
+#define LORA_MOSI (27)
+#define LORA_RST  (14)
+#define LORA_IRQ  (26)
+#define LORA_IO1  (33)
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+#endif

shared/hal/eboxtube.h

@@ -0,0 +1,32 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+
+#ifndef _EBOXTUBE_H
+#define _EBOXTUBE_H
+
+#include <stdint.h>
+
+// Hardware related definitions for ebox ESP32-bit with external connected RFM95 LoRa
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1
+
+#define HAS_LED (22)     // Green LED on board
+#define RGB_LED_COUNT 1 // we have 1 LED
+#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_2, GRB>(leds, RGB_LED_COUNT);
+#define HAS_BUTTON (0)   // button "FLASH" on board
+#define DISABLE_BROWNOUT 1      // comment out if you want to keep brownout feature
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (18)
+#define LORA_MISO (19)
+#define LORA_MOSI (27)
+#define LORA_RST  (14)
+#define LORA_IRQ  (26)
+#define LORA_IO1  (33)
+#define LORA_IO2  (32)
+
+#endif

shared/hal/ecopower.h

@@ -0,0 +1,56 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+#ifndef _GENERIC_H
+#define _GENERIC_H
+
+#include <stdint.h>
+
+#define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no LoRa
+#define CFG_sx1276_radio 1 // select LoRa chip
+
+//#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_DISPLAY 1
+//#define MY_DISPLAY_FLIP  1 // use if display is rotated
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BAT_VOLTAGE_DIVIDER ((82.0+220.0)/82.0) // 82k + 220k 1%
+//#define BAT_MEASURE_EN   EXT_POWER_SW  // Turn power on for measurement
+
+#define EXT_POWER_SW    15            // Switch VDD on pin JP10, needed for RTC DS3231
+#define EXT_POWER_ON    0
+
+#define HAS_LED (2) // on board green LED
+#define HAS_TWO_LED (12) // on board red LED
+//#define HAS_BUTTON (0) // on board button -> don't use, is same as RTC_INT!
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA SDA
+#define MY_DISPLAY_SCL SCL
+#define MY_DISPLAY_RST NOT_A_PIN
+
+// Settings for on board DS3231 RTC chip
+// note: to use RTC_INT, capacitor 100nF next to red LED must be removed to sharpen interrupt signal slope
+// and setting EXT_POWER_ON is needed (this is done in main.cpp)
+#define HAS_RTC MY_DISPLAY_SDA, MY_DISPLAY_SCL // SDA, SCL
+#define RTC_INT GPIO_NUM_0 //
+
+// Settings for IF482 interface
+//#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_3, GPIO_NUM_1 // RX, TX
+
+// Settings for DCF77 interface
+//#define HAS_DCF77 GPIO_NUM_14 // JP8 #13
+//#define DCF77_ACTIVE_LOW 1
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  SCK 
+#define LORA_CS   SS
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST  (17)
+#define LORA_IRQ  (16)
+#define LORA_IO1  (14) // JP8 #13 to be external wired
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+#endif

shared/hal/fipy.h

@@ -0,0 +1,34 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+#ifndef _FIPY_H
+#define _FIPY_H
+
+#include <stdint.h>
+
+// Hardware related definitions for Pycom FiPy Board
+
+#define HAS_LORA 1 // comment out if device shall not send data via LoRa
+
+#define CFG_sx1272_radio 1
+#define HAS_LED NOT_A_PIN      // FiPy has no on board LED, so we use RGB LED
+#define RGB_LED_COUNT 1 // we have 1 LED
+#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_0, GRB>(leds, RGB_LED_COUNT);
+#define BOARD_HAS_PSRAM        // use extra 4MB extern RAM
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (18)
+#define LORA_MISO (19)
+#define LORA_MOSI (27)
+#define LORA_RST  LMIC_UNUSED_PIN
+#define LORA_IRQ  (23) // LoRa IRQ
+#define LORA_IO1  (23) // Pin tied via diode to DIO0
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+// select WIFI antenna (internal = onboard / external = u.fl socket)
+#define HAS_ANTENNA_SWITCH GPIO_NUM_21 // pin for switching wifi antenna
+#define WIFI_ANTENNA 0                 // 0 = internal, 1 = external
+
+#endif

shared/hal/generic.h

@@ -0,0 +1,108 @@
+// clang-format off
+// upload_speed 115200
+// board esp32dev
+
+#ifndef _GENERIC_H
+#define _GENERIC_H
+
+#include <stdint.h>
+
+// Hardware related definitions for generic ESP32 boards
+// generic.h is kitchensink with all available options
+
+#define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no LoRa
+//#define HAS_SPI 1  // comment out if device shall not send data via SPI
+// pin definitions for SPI slave interface
+//#define SPI_MOSI GPIO_NUM_23
+//#define SPI_MISO GPIO_NUM_19
+//#define SPI_SCLK GPIO_NUM_18
+//#define SPI_CS   GPIO_NUM_5
+
+// enable only if you want to store a local paxcount table on the device
+#define HAS_SDCARD  1      // this board has an SD-card-reader/writer
+// Pins for SD-card
+#define SDCARD_CS    (13)
+#define SDCARD_MOSI  (15)
+#define SDCARD_MISO  (2)
+#define SDCARD_SCLK  (14)
+
+// enable only if device has these sensors, otherwise comment these lines
+// tutorial to connect BME sensor see here:
+// https://sbamueller.wordpress.com/2019/02/26/paxcounter-mit-umweltsensor/
+//
+// in platformio.ini append
+// lib_deps = <...> ${common.lib_deps_sensors}
+// for loading necessary libraries
+
+// BME680 sensor on I2C bus
+//#define HAS_BME 1 // Enable BME sensors in general
+//#define HAS_BME680 GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
+//#define BME680_ADDR BME68X_I2C_ADDR_LOW // connect SDIO of BME680 to GND
+
+// BME280 sensor on I2C bus
+//#define HAS_BME 1 // Enable BME sensors in general
+//#define HAS_BME280 GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
+//#define BME280_ADDR 0x76 // change to 0x77 depending on your wiring
+
+// BMP180 sensor on I2C bus
+//#define HAS_BMP180
+//#define BMP180_ADDR 0x77
+
+// SDS011 dust sensor settings
+//#define HAS_SDS011 1 // use SDS011
+// used pins on the ESP-side:
+//#define SDS_TX 19     // connect to RX on the SDS011
+//#define SDS_RX 23     // connect to TX on the SDS011
+
+// up to three user defined sensors (if connected)
+//#define HAS_SENSOR_1 1 // comment out if device has user defined sensor #1
+//#define HAS_SENSOR_2 1 // comment out if device has user defined sensor #2
+//#define HAS_SENSOR_3 1 // comment out if device has user defined sensor #3
+
+#define CFG_sx1276_radio 1 // select LoRa chip
+//#define CFG_sx1272_radio 1 // select LoRa chip
+//#define BOARD_HAS_PSRAM // use if board has external SPIRAM, note: this will reduce IRAM0 by 64KB for SPIRAM cache
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+//#define HAS_DISPLAY 1
+//#define MY_DISPLAY_FLIP  1 // use if display is rotated
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
+
+#define HAS_LED (21) // on board  LED
+#define HAS_BUTTON (39) // on board button
+//#define RGB_LED_COUNT 1 // we have 1 LED
+//#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_0, GRB>(leds, RGB_LED_COUNT);
+
+// GPS settings
+//#define HAS_GPS 1 // use on board GPS
+//#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M RX, TX
+//#define GPS_INT GPIO_NUM_13 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO13
+
+// Pins for I2C interface of OLED Display
+//#define MY_DISPLAY_SDA (4)
+//#define MY_DISPLAY_SCL (15)
+//#define MY_DISPLAY_RST (16)
+
+// Settings for on board DS3231 RTC chip
+//#define HAS_RTC MY_DISPLAY_SDA, MY_DISPLAY_SCL // SDA, SCL
+//#define RTC_INT GPIO_NUM_34 // timepulse with accuracy +/- 2*e-6 [microseconds] = 0,1728sec / day
+
+// Settings for IF482 interface
+//#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters
+
+// Settings for DCF77 interface
+//#define HAS_DCF77 GPIO_NUM_1
+//#define DCF77_ACTIVE_LOW 1
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (18)
+#define LORA_MISO (19)
+#define LORA_MOSI (27)
+#define LORA_RST  (14)
+#define LORA_IRQ  (26)
+#define LORA_IO1  (33)
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+#endif

shared/hal/heltec.h

@@ -0,0 +1,36 @@
+// clang-format off
+// upload_speed 921600
+// board heltec_wifi_lora_32
+
+#ifndef _HELTEC_H
+#define _HELTEC_H
+
+#include <stdint.h>
+
+// Hardware related definitions for Heltec V1 LoRa-32 Board
+// see https://docs.heltec.org/en/node/esp32/dev-board/hardware_update_log.html#v1
+
+#define HAS_LORA 1 // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1
+
+#define HAS_DISPLAY 1 // OLED-Display on board
+#define HAS_LED LED_BUILTIN                           // white LED on board (set to NOT_A_PIN to disable)
+#define HAS_BUTTON KEY_BUILTIN                        // button "PROG" on board
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA SDA_OLED
+#define MY_DISPLAY_SCL SCL_OLED
+#define MY_DISPLAY_RST RST_OLED
+
+// Pins for LORA chip SPI interface come from board file, we need some
+// additional definitions for LMIC
+#define LORA_IRQ DIO0
+#define LORA_IO1 DIO1
+#define LORA_IO2 DIO2
+#define LORA_SCK SCK
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST RST_LoRa
+#define LORA_CS SS
+
+#endif

shared/hal/heltecv2.h

@@ -0,0 +1,44 @@
+// clang-format off
+// upload_speed 921600
+// board heltec_wifi_lora_32_V2
+
+#ifndef _HELTECV2_H
+#define _HELTECV2_H
+
+#include <stdint.h>
+
+// Hardware related definitions for Heltec V2 LoRa-32 Board
+// see https://docs.heltec.org/en/node/esp32/dev-board/hardware_update_log.html#v2
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1
+
+#define HAS_DISPLAY 1 // OLED-Display on board
+#define HAS_LED LED_BUILTIN                           // white LED on board (set to NOT_A_PIN to disable)
+#define HAS_BUTTON KEY_BUILTIN                        // button "PROG" on board
+
+#define BAT_MEASURE_ADC ADC2_GPIO13_CHANNEL  // battery probe GPIO pin
+#define BAT_MEASURE_ADC_UNIT 2 // ADC 2
+#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 220k/100k on board
+
+// switches battery power and Vext, switch logic 0 = on / 1 = off
+#define EXT_POWER_SW Vext
+#define EXT_POWER_ON 0
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA SDA_OLED
+#define MY_DISPLAY_SCL SCL_OLED
+#define MY_DISPLAY_RST RST_OLED
+
+// Pins for LORA chip SPI interface come from board file, we need some
+// additional definitions for LMIC
+#define LORA_IRQ DIO0
+#define LORA_IO1 DIO1
+#define LORA_IO2 DIO2
+#define LORA_SCK SCK
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST RST_LoRa
+#define LORA_CS SS
+
+#endif

shared/hal/heltecv21.h

@@ -0,0 +1,43 @@
+// clang-format off
+// upload_speed 921600
+// board heltec_wifi_lora_32_V2
+
+#ifndef _HELTECV21_H
+#define _HELTECV21_H
+
+#include <stdint.h>
+
+// Hardware related definitions for Heltec V2.1 LoRa-32 Board
+// see https://docs.heltec.org/en/node/esp32/dev-board/hardware_update_log.html#v2-1
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1
+
+#define HAS_DISPLAY 1 // OLED-Display on board
+#define HAS_LED LED_BUILTIN                           // white LED on board (set to NOT_A_PIN to disable)
+#define HAS_BUTTON KEY_BUILTIN                        // button "PROG" on board
+
+#define BAT_MEASURE_ADC ADC1_GPIO37_CHANNEL  // battery probe GPIO pin
+#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 220k/100k on board
+
+// switches battery power and Vext, switch logic 0 = on / 1 = off
+#define EXT_POWER_SW Vext
+#define EXT_POWER_ON 0
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA SDA_OLED
+#define MY_DISPLAY_SCL SCL_OLED
+#define MY_DISPLAY_RST RST_OLED
+
+// Pins for LORA chip SPI interface come from board file, we need some
+// additional definitions for LMIC
+#define LORA_IRQ DIO0
+#define LORA_IO1 DIO1
+#define LORA_IO2 DIO2
+#define LORA_SCK SCK
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST RST_LoRa
+#define LORA_CS SS
+
+#endif

shared/hal/lolin32lite.h

@@ -0,0 +1,21 @@
+// clang-format off
+// upload_speed 921600
+// board lolin32
+
+#ifndef _LOLINLITE_H
+#define _LOLINLITE_H
+
+#include <stdint.h>
+
+// Hardware related definitions for lolin32lite (without LoRa shield)
+
+#define HAS_LED LED_BUILTIN // on board LED on GPIO5
+#define LED_ACTIVE_LOW 1    // Onboard LED is active when pin is LOW (set to NOT_A_PIN to disable)
+
+#define MY_SDA SDA
+#define MY_SCL SCL
+
+// disable brownout detection (avoid unexpected reset on some boards)
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#endif

shared/hal/lolin32litelora.h

@@ -0,0 +1,47 @@
+// clang-format off
+// upload_speed 921600
+// board lolin32
+
+#ifndef _LOLINLITELORA_H
+#define _LOLINLITELORA_H
+
+#include <stdint.h>
+
+// Hardware related definitions for lolin32 lite with loraNode32 shield
+// See https://github.com/hallard/LoLin32-Lite-Lora
+
+// disable brownout detection (avoid unexpected reset on some boards)
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_DISPLAY 1 // OLED-Display on board
+//#define MY_DISPLAY_FLIP  1 // uncomment this for rotated display
+#define HAS_LED       22  // ESP32 GPIO12 (pin22) On Board LED (set to NOT_A_PIN to disable)
+#define LED_ACTIVE_LOW 1  // Onboard LED is active when pin is LOW
+#define RGB_LED_COUNT 1 // we have 1 LED
+#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_0, GRB>(leds, RGB_LED_COUNT);
+#define HAS_BUTTON    15  // ESP32 GPIO15 (pin15) Button is on the LoraNode32 shield
+#define BUTTON_PULLUP  1  // Button need pullup instead of default pulldown
+
+#define HAS_LORA  1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // RFM95 module
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  SCK 
+#define LORA_CS   SS
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST  (25)
+#define LORA_IRQ  (27)
+#define LORA_IO1  (26)
+#define LORA_IO2  (4)
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA (12)
+#define MY_DISPLAY_SCL (14)
+#define MY_DISPLAY_RST NOT_A_PIN
+
+// I2C config for Microchip 24AA02E64 DEVEUI unique address
+#define MCP_24AA02E64_I2C_ADDRESS 0x50 // I2C address for the 24AA02E64 
+#define MCP_24AA02E64_MAC_ADDRESS 0xF8 // Memory adress of unique deveui 64 bits
+
+#endif

shared/hal/lolin32lora.h

@@ -0,0 +1,48 @@
+// clang-format off
+// upload_speed 921600
+// board lolin32
+
+#ifndef _LOLINLORA_H
+#define _LOLINLORA_H
+
+#include <stdint.h>
+
+// Hardware related definitions for lolin32 with loraNode32 shield
+// See https://github.com/hallard/LoLin32-Lora
+
+// disable brownout detection (avoid unexpected reset on some boards)
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_DISPLAY 1 // OLED-Display on board
+//#define MY_DISPLAY_FLIP  1 // uncomment this for rotated display
+#define HAS_LED NOT_A_PIN // Led os on same pin as Lora SS pin, to avoid problems, we don't use it
+#define LED_ACTIVE_LOW 1  // Onboard LED is active when pin is LOW
+                          // Anyway shield is on over the LoLin32 board, so we won't be able to see this LED
+#define RGB_LED_COUNT 1 // we have 1 LED
+#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_13, GRB>(leds, RGB_LED_COUNT);
+#define HAS_BUTTON    15  // ESP32 GPIO15 (pin15) Button is on the LoraNode32 shield
+#define BUTTON_PULLUP  1  // Button need pullup instead of default pulldown
+
+#define HAS_LORA  1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // RFM95 module
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  SCK 
+#define LORA_CS   SS
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST  (25)
+#define LORA_IRQ  (27)
+#define LORA_IO1  (26)
+#define LORA_IO2  (4)
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA SDA
+#define MY_DISPLAY_SCL SCL
+#define MY_DISPLAY_RST NOT_A_PIN
+
+// I2C config for Microchip 24AA02E64 DEVEUI unique address
+#define MCP_24AA02E64_I2C_ADDRESS 0x50 // I2C address for the 24AA02E64 
+#define MCP_24AA02E64_MAC_ADDRESS 0xF8 // Memory adress of unique deveui 64 bits
+
+#endif

shared/hal/lopy.h

@@ -0,0 +1,33 @@
+// clang-format off
+// upload_speed 921600
+// board lopy
+
+#ifndef _LOPY_H
+#define _LOPY_H
+
+#include <stdint.h>
+
+// Hardware related definitions for Pycom LoPy Board (NOT LoPy4)
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1272_radio 1
+#define HAS_LED NOT_A_PIN // LoPy4 has no on board mono LED, we use on board RGB LED
+#define RGB_LED_COUNT 1 // we have 1 LED
+#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_0, GRB>(leds, RGB_LED_COUNT);
+
+// Note: Pins for LORA chip SPI interface come from board file pins_arduino.h
+
+// select WIFI antenna (internal = onboard / external = u.fl socket)
+#define HAS_ANTENNA_SWITCH  (16)      // pin for switching wifi antenna
+#define WIFI_ANTENNA 0              // 0 = internal, 1 = external
+
+// uncomment this only if your LoPy runs on a EXPANSION BOARD
+//#define HAS_LED (12) // use if LoPy is on Expansion Board, this has a user LED
+//#define LED_ACTIVE_LOW 1 // use if LoPy is on Expansion Board, this has a user LED
+//#define HAS_BUTTON (13) // user button on expansion board
+//#define BUTTON_PULLUP 1  // Button need pullup instead of default pulldown
+//#define BAT_MEASURE_ADC ADC1_GPIO39_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+//#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 1MOhm/1MOhm -> expansion board 3.0
+//#define BAT_VOLTAGE_DIVIDER 4 // voltage divider 115kOhm/56kOhm -> expansion board 2.0
+
+#endif

shared/hal/lopy4.h

@@ -0,0 +1,42 @@
+// clang-format off
+// upload_speed 921600
+// board lopy4
+
+#ifndef _LOPY4_H
+#define _LOPY4_H
+
+#include <stdint.h>
+
+// Hardware related definitions for Pycom LoPy4 Board
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+
+//#defin HAS_SPI 1        // comment out if device shall not send data via SPI
+// pin definitions for local wired SPI slave interface
+//#define SPI_MOSI  GPIO_NUM_22
+//#define SPI_MISO  GPIO_NUM_33
+//#define SPI_SCLK  GPIO_NUM_26
+//#define SPI_CS    GPIO_NUM_36
+
+#define CFG_sx1276_radio 1
+#define HAS_LED NOT_A_PIN // LoPy4 has no on board mono LED, we use on board RGB LED
+#define RGB_LED_COUNT 1 // we have 1 LED
+#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_0, GRB>(leds, RGB_LED_COUNT);
+#define BOARD_HAS_PSRAM // use extra 4MB extern RAM
+
+// Note: Pins for LORA chip SPI interface come from board file pins_arduino.h
+
+// select WIFI antenna (internal = onboard / external = u.fl socket)
+#define HAS_ANTENNA_SWITCH  (21) // pin for switching wifi antenna (P12)
+#define WIFI_ANTENNA 0    // 0 = internal, 1 = external
+
+// uncomment defines in this section ONLY if your LoPy lives on a EXPANSION BOARD
+//#define HAS_LED (12) // use if LoPy is on Expansion Board, this has a user LED
+//#define LED_ACTIVE_LOW 1 // use if LoPy is on Expansion Board, this has a user LED
+//#define HAS_BUTTON (13) // user button on expansion board
+//#define BUTTON_PULLUP 1  // Button need pullup instead of default pulldown
+//#define BAT_MEASURE_ADC ADC1_GPIO39_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+//#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 1MOhm/1MOhm -> expansion board 3.0
+//#define BAT_VOLTAGE_DIVIDER 4 // voltage divider 115kOhm/56kOhm -> expansion board 2.0
+
+#endif

shared/hal/m5core.h

@@ -0,0 +1,61 @@
+// clang-format off
+// upload_speed 921600
+// board m5stack-core-esp32
+
+#ifndef _M5CORE_H
+#define _M5CORE_H
+
+#include <stdint.h>
+
+#define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no M5 RA01 LoRa module
+#define LORA_SCK  SCK
+#define LORA_CS   SS
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST  GPIO_NUM_26
+#define LORA_IRQ  GPIO_NUM_36
+#define LORA_IO1  GPIO_NUM_34 // must be wired by you on PCB!
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+// enable only if you want to store a local paxcount table on the device
+#define HAS_SDCARD  1      // this board has an SD-card-reader/writer
+// Pins for SD-card
+#define SDCARD_CS    GPIO_NUM_4
+#define SDCARD_MOSI  MOSI
+#define SDCARD_MISO  MISO
+#define SDCARD_SCLK  SCK
+
+#define CFG_sx1276_radio 1 // select LoRa chip
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_LED NOT_A_PIN // no on board LED (?)
+#define HAS_BUTTON (39) // on board button A
+
+// power management settings
+#define HAS_IP5306 1 // has IP5306 chip
+#define PMU_CHG_CURRENT 2 // battery charge current
+// possible values: 0:200mA, 1:400mA, *2:500mA, 3:600mA
+#define PMU_CHG_CUTOFF 0 // battery charge cutoff
+// possible values: *0:4.2V, 1:4.3V, 2:4.35V, 3:4.4V
+
+// Optional GPS Module settings
+//#define HAS_GPS 1 // use GPS
+//#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_17, GPIO_NUM_16 // UBlox NEO M8N RX,TX
+//#define GPS_INT GPIO_NUM_36 // 30ns accurary timepulse, to be external wired on pcb: shorten R12!
+
+// Display Settings
+#define HAS_DISPLAY 2   // TFT-LCD
+//#define MY_DISPLAY_FLIP  1 // use if display is rotated
+#define MY_DISPLAY_WIDTH 320
+#define MY_DISPLAY_HEIGHT 240
+#define TFT_MOSI MOSI   // SPI
+#define TFT_MISO MISO   // SPI
+#define TFT_SCLK SCK    // SPI
+#define TFT_CS   GPIO_NUM_14    // Chip select control
+#define TFT_DC   GPIO_NUM_27    // Data Command control
+#define TFT_RST  GPIO_NUM_33    // Reset
+#define TFT_BL   GPIO_NUM_32    // LED back-light
+#define TFT_FREQUENCY 40000000
+#define TFT_TYPE LCD_ILI9341, FLAGS_NONE, TFT_FREQUENCY, TFT_CS, TFT_DC, TFT_RST, TFT_BL, TFT_MISO, TFT_MOSI, TFT_SCLK
+
+#endif

shared/hal/m5fire.h

@@ -0,0 +1,66 @@
+// clang-format off
+// upload_speed 921600
+// board m5stack-fire
+
+// note use of GPIO16/17
+// https://www.bjoerns-techblog.de/2019/03/m5stack-fire-eine-uebersicht/
+
+#ifndef _M5FIRE_H
+#define _M5FIRE_H
+
+#include <stdint.h>
+
+#define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no M5 RA01 LoRa module
+#define LORA_SCK  SCK
+#define LORA_CS   SS
+#define LORA_MISO MISO
+#define LORA_MOSI MOSI
+#define LORA_RST  GPIO_NUM_26
+#define LORA_IRQ  GPIO_NUM_36
+#define LORA_IO1  GPIO_NUM_34 // must be wired by you on PCB!
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+// enable only if you want to store a local paxcount table on the device
+//#define HAS_SDCARD  1      // this board has an SD-card-reader/writer
+//#define SDCARD_CS    GPIO_NUM_4
+//#define SDCARD_MOSI  MOSI
+//#define SDCARD_MISO  MISO
+//#define SDCARD_SCLK  SCK
+
+#define CFG_sx1276_radio 1 // select LoRa chip
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_LED NOT_A_PIN // no on board LED (?)
+//#define RGB_LED_COUNT 10 // M5fire has a stripe of 10 RGB Pixels
+//#define HAS_RGB_LED FastLED.addLeds<SK6812, GPIO_NUM_15, GRB>(leds, RGB_LED_COUNT);
+#define HAS_BUTTON (39) // on board button A
+
+// power management settings
+#define HAS_IP5306 1 // has IP5306 chip
+#define PMU_CHG_CURRENT 2 // battery charge current
+// possible values: 0:200mA, 1:400mA, *2:500mA, 3:600mA
+#define PMU_CHG_CUTOFF 0 // battery charge cutoff
+// possible values: *0:4.2V, 1:4.3V, 2:4.35V, 3:4.4V
+
+// Optional GPS Module settings
+//#define HAS_GPS 1 // use GPS
+//#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_5, GPIO_NUM_13 // to be external wired on pcb: open R1 & R4, and shorten R2 & R5
+//#define GPS_INT GPIO_NUM_36 // 30ns accurary timepulse, to be external wired on pcb: shorten R12!
+
+// Display Settings
+#define HAS_DISPLAY 2   // TFT-LCD
+//#define MY_DISPLAY_FLIP  1 // use if display is rotated
+#define MY_DISPLAY_WIDTH 320
+#define MY_DISPLAY_HEIGHT 240
+#define TFT_MOSI MOSI   // SPI
+#define TFT_MISO MISO   // SPI
+#define TFT_SCLK SCK    // SPI
+#define TFT_CS   GPIO_NUM_14    // Chip select control
+#define TFT_DC   GPIO_NUM_27    // Data Command control
+#define TFT_RST  GPIO_NUM_33    // Reset
+#define TFT_BL   GPIO_NUM_32    // LED back-light
+#define TFT_FREQUENCY 40000000
+#define TFT_TYPE LCD_ILI9341, FLAGS_NONE, TFT_FREQUENCY, TFT_CS, TFT_DC, TFT_RST, TFT_BL, TFT_MISO, TFT_MOSI, TFT_SCLK
+
+
+#endif

shared/hal/octopus32.h

@@ -0,0 +1,50 @@
+// clang-format off
+// upload_speed 921600
+// board featheresp32
+
+#ifndef _OCTOPUS_H
+#define _OCTOPUS_H
+#include <stdint.h>
+
+// Hardware related definitions for #IoT Octopus32 with the Adafruit LoRaWAN Wing
+// You can use this configuration also with the Adafruit ESP32 Feather + the LoRaWAN Wing
+// In this config we use the Adafruit OLED Wing which is only 128x32 pixel, need to find a smaller font
+// NOTE: if LORA_IRQ and LORA_IO1 are tied to the same GPIO using diodes on the board, 
+// you must disable LMIC_USE_INTERRUPTS in lmic_config.h
+
+// disable brownout detection (avoid unexpected reset on some boards)
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+// Octopus32 has a pre-populated BME680 on i2c addr 0x76
+#define HAS_BME 1 // Enable BME sensors in general
+#define HAS_BME680 GPIO_NUM_23, GPIO_NUM_22 // SDA, SCL
+#define BME680_ADDR BME68X_I2C_ADDR_LOW // connect SDIO of BME680 to GND
+
+#define HAS_LED        13  // ESP32 GPIO12 (pin22) On Board LED
+//#define LED_ACTIVE_LOW 1  // Onboard LED is active when pin is LOW
+//#define RGB_LED_COUNT 1 // we have 1 LED
+//#define HAS_RGB_LED FastLED.addLeds<WS2812, GPIO_NUM_13, GRB>(leds, RGB_LED_COUNT);
+//#define HAS_BUTTON    15  // ESP32 GPIO15 (pin15) Button is on the LoraNode32 shield
+//#define BUTTON_PULLUP  1  // Button need pullup instead of default pulldown
+
+#define HAS_LORA  1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // RFM95 module
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (14)
+#define LORA_MISO (19)
+#define LORA_MOSI (18)
+#define LORA_RST  LMIC_UNUSED_PIN
+#define LORA_IRQ  (33)
+#define LORA_IO1  (33)
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+// Pins for I2C interface of OLED Display
+#define HAS_DISPLAY 1
+//#define MY_DISPLAY_FLIP  1 // uncomment this for rotated display 
+#define MY_DISPLAY_SDA (23)
+#define MY_DISPLAY_SCL (22)
+#define MY_DISPLAY_RST NOT_A_PIN 
+
+#endif

shared/hal/olimexpoeiso.h

@@ -0,0 +1,30 @@
+// clang-format off
+// upload_speed 921600
+// board esp32-poe-iso
+
+#ifndef _OLIMEXPOEISO_H
+#define _OLIMEXPOEISO_H
+
+#include <stdint.h>
+
+// enable only if you want to store a local paxcount table on the device
+//#define HAS_SDCARD 2 // this board has a SDMMC card-reader/writer
+
+// enable only if you want to send paxcount via ethernet port to mqtt server
+#define HAS_MQTT 1  // use MQTT on ethernet interface
+
+//#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery measurement
+//#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 470k/470k on board
+#define BAT_MEASURE_ADC ADC1_GPIO39_CHANNEL // external power sense
+#define BAT_VOLTAGE_DIVIDER 2.1277f // voltage divider 47k/100k on board
+
+#define HAS_BUTTON KEY_BUILTIN // on board button
+#define HAS_LED NOT_A_PIN // no on board LED
+
+//#define HAS_DISPLAY 1
+//#define MY_DISPLAY_FLIP  1 // use if display is rotated
+//#define MY_DISPLAY_SDA SDA
+//#define MY_DISPLAY_SCL SCL
+//#define MY_DISPLAY_RST NOT_A_PIN
+
+#endif

shared/hal/tinypico.h

@@ -0,0 +1,24 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+
+#ifndef _TINYPICO_H
+#define _TINYPICO_H
+
+#include <stdint.h>
+
+// Hardware related definitions for crowdsupply tinypico board
+
+#define HAS_LED NOT_A_PIN     // Green LED on board
+#define HAS_RGB_LED FastLED.addLeds<APA102, GPIO_NUM_2, GPIO_NUM_12, BGR>(leds, RGB_LED_COUNT)
+
+//#define DISABLE_BROWNOUT 1      // comment out if you want to keep brownout feature
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BAT_VOLTAGE_DIVIDER 2.7625f // voltage divider 160k/442k on board
+#define BOARD_HAS_PSRAM // use extra 4MB external RAM
+#define LED_POWER_SW (13) // switches LED power
+#define LED_POWER_ON 0 // switch on transistor for LED power
+#define LED_POWER_OFF 1
+
+#endif

shared/hal/tinypicomatrix.h

@@ -0,0 +1,46 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+
+#ifndef _TINYPICO_H
+#define _TINYPICO_H
+
+#include <stdint.h>
+
+// Hardware related definitions for crowdsupply tinypico board
+// for operating a 96x16 shift register LED matrix display
+
+#define HAS_LED NOT_A_PIN     // Green LED on board
+#define HAS_RGB_LED FastLED.addLeds<APA102, GPIO_NUM_2, GPIO_NUM_12, BGR>(leds, RGB_LED_COUNT)
+
+//#define DISABLE_BROWNOUT 1      // comment out if you want to keep brownout feature
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BAT_VOLTAGE_DIVIDER 2.7625f // voltage divider 160k/442k on board
+#define BOARD_HAS_PSRAM // use extra 4MB external RAM
+#define LED_POWER_SW (13) // switches LED power
+#define LED_POWER_ON 0 // switch on transistor for LED power
+#define LED_POWER_OFF 1
+
+// LED Matrix display settings
+#define HAS_MATRIX_DISPLAY              1       // Uncomment to enable LED matrix display output
+#define LED_MATRIX_WIDTH                (32*2)  // Width (cols) in pixels (LEDs) of your display, must be 32X
+#define LED_MATRIX_HEIGHT               (16*1)  // Height (rows) in pixels (LEDs) of your display, must be 16X
+
+// Explanation of pin signals see https://learn.adafruit.com/32x16-32x32-rgb-led-matrix/new-wiring
+#define MATRIX_DISPLAY_SCAN_US          500     // Matrix display scan rate in microseconds (1ms is about 'acceptable')
+#define LED_MATRIX_LATCHPIN             32      // LAT (or STB = Strobe)
+#define LED_MATRIX_CLOCKPIN             33      // CLK
+#define LED_MATRIX_EN_74138             21      // EN (or OE)
+#define LED_MATRIX_LA_74138             23      // LA (or A)
+#define LED_MATRIX_LB_74138             19      // LB (or B)
+#define LED_MATRIX_LC_74138             18      // LC (or C)
+#define LED_MATRIX_LD_74138             5       // LD (or D)
+#define LED_MATRIX_DATA_R1              22      // R1 (or R0)
+
+// CLK: The clock signal moves the data bits from pin R1 ("red") in the shift registers
+// LAT: The latch signal enables LEDs according to the shift register's contents
+// Line Selects: LA, LB, LC, LD select which rows of the display are currently lit (0 .. 15)
+// OE: Output enable switches the LEDs on/off while transitioning from one row to the next
+
+#endif

shared/hal/ttgobeam.h

@@ -0,0 +1,44 @@
+// clang-format off
+// upload_speed 921600
+// board ttgo-t-beam
+
+#ifndef _TTGOBEAM_H
+#define _TTGOBEAM_H
+
+#include <stdint.h>
+
+// Hardware related definitions for TTGO T-Beam board
+// (only) for older T-Beam version T22_V05 eternal wiring LORA_IO1 to GPIO33 is needed!
+//
+// pinouts taken from http://tinymicros.com/wiki/TTGO_T-Beam
+
+#define HAS_LED GPIO_NUM_14 // on board green LED, only new version TTGO-BEAM V07
+//#define HAS_LED GPIO_NUM_21 // on board green LED, only old verison TTGO-BEAM V05
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+#define HAS_BUTTON GPIO_NUM_39 // on board button (next to reset)
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
+
+// GPS settings
+#define HAS_GPS 1 // use on board GPS
+#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M
+//#define GPS_INT GPIO_NUM_34 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO34
+
+// enable only if device has these sensors, otherwise comment these lines
+// BME680 sensor on I2C bus
+//#define HAS_BME 1 // Enable BME sensors in general
+//#define HAS_BME680 SDA, SCL
+//#define BME680_ADDR BME68X_I2C_ADDR_LOW // !! connect SDIO of BME680 to GND !!
+
+// display (if connected)
+//#define HAS_DISPLAY 1
+#define MY_DISPLAY_SDA SDA
+#define MY_DISPLAY_SCL SCL
+#define MY_DISPLAY_RST NOT_A_PIN
+//#define MY_DISPLAY_FLIP  1 // use if display is rotated
+
+//#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#endif

shared/hal/ttgobeam10.h

@@ -0,0 +1,80 @@
+// clang-format off
+// upload_speed 921600
+// board ttgo-t-beam
+
+#ifndef _TTGOBEAM_H
+#define _TTGOBEAM_H
+
+#include <stdint.h>
+
+/* 
+Hardware related definitions for TTGO T-Beam board
+for T-Beam version T22_V10 + T22_V11
+pinouts taken from https://github.com/lewisxhe/TTGO-T-Beam
+
+/// Button functions: ///
+Power, short press -> set device on / while device is on: goto sleep
+Power, long press   -> set device off
+User, short press   -> flip display page 
+User, long press    -> send a button message
+Reset -> reset device
+*/
+
+#define HAS_DISPLAY 1
+#define MY_DISPLAY_SDA SDA
+#define MY_DISPLAY_SCL SCL
+#define MY_DISPLAY_RST NOT_A_PIN
+//#define MY_DISPLAY_FLIP  1 // use if display is rotated
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+#define HAS_BUTTON GPIO_NUM_38 // middle on board button
+#define HAS_LED GPIO_NUM_4 // not present on all T-Beam 1.0 boards
+#define LED_ACTIVE_LOW 1
+
+// power management settings
+#define HAS_PMU 1 // has AXP192 chip
+#define XPOWERS_CHIP_AXP192 1
+#define PMU_INT GPIO_NUM_35 // battery interrupt
+#define PMU_CHG_CURRENT XPOWERS_AXP192_CHG_CUR_1000MA // battery charge current
+// possible values (mA):
+// 100/190/280/360/450/550/630/700/780/880/960/1000/1080/1160/1240/1320
+#define PMU_CHG_CUTOFF XPOWERS_AXP192_CHG_VOL_4V2 // battery charge cutoff
+// possible values (V):
+// 4V1/4V15/4V2/4V36
+
+// GPS settings
+#define HAS_GPS 1 // use on board GPS
+#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_34, GPIO_NUM_12 // UBlox NEO 6M
+#define GPS_INT GPIO_NUM_37 // 30ns accurary timepulse generated by NEO 6M Pin #3
+
+// enable only if device has these sensors, otherwise comment these lines
+// BME680 sensor on I2C bus
+//#define HAS_BME 1 // Enable BME sensors in general
+//#define HAS_BME680 SDA, SCL
+//#define BME680_ADDR BME68X_I2C_ADDR_LOW // !! connect SDIO of BME680 to GND !!
+
+//#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#endif
+
+/*
+
+// T-Beam V10/V11 has on board power management by AXP192 PMU chip:
+//
+// DCDC1 0.7-3.5V @ 1200mA -> OLED
+// DCDC3 0.7-3.5V @ 700mA -> ESP32 (keep this on!)
+// LDO1 30mA -> GPS Backup
+// LDO2 200mA -> LORA
+// LDO3 200mA -> GPS
+
+// Wiring for I2C OLED display:
+//
+// Signal     Header   OLED
+// 3V3         7       VCC
+// GND         8       GND
+// IO22(SCL)   9       SCL
+// IO21(SDA)   10      SDA
+//
+
+*/

shared/hal/ttgofox.h

@@ -0,0 +1,48 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+#ifndef _TTGOFOX_H
+#define _TTGOFOX_H
+
+#include <stdint.h>
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+
+#define HAS_DISPLAY 1
+#define HAS_LED NOT_A_PIN // green on board LED is useless, is GPIO25, which switches power for Lora+Display
+
+#define EXT_POWER_SW GPIO_NUM_25 // switches power for LoRa chip
+#define EXT_POWER_ON    0
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL
+#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
+#define HAS_BUTTON GPIO_NUM_36 // on board button (next to reset)
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA (21)
+#define MY_DISPLAY_SCL (22)
+#define MY_DISPLAY_RST NOT_A_PIN
+
+// Settings for on board DS3231 RTC chip
+#define HAS_RTC MY_DISPLAY_SDA, MY_DISPLAY_SCL // SDA, SCL
+#define RTC_INT GPIO_NUM_34 // timepulse with accuracy +/- 2*e-6 [microseconds] = 0,1728sec / day
+
+// Settings for IF482 interface
+#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters
+
+// Settings for DCF77 interface
+//#define HAS_DCF77 GPIO_NUM_14
+//#define DCF77_ACTIVE_LOW 1
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (18)
+#define LORA_MISO (19)
+#define LORA_MOSI (27)
+#define LORA_RST  (23)
+#define LORA_IRQ  (26)
+#define LORA_IO1  (33)
+#define LORA_IO2  (32)
+
+#endif

shared/hal/ttgotdisplay.h

@@ -0,0 +1,26 @@
+// clang-format off
+// upload_speed 1500000
+// board esp32dev
+
+#ifndef _TTGOTDISPLAY_H
+#define _TTGOTDISPLAY_H
+
+#include <stdint.h>
+
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_LED NOT_A_PIN  // no on board LED (?)
+#define HAS_BUTTON (35)    // on board button A
+
+// power management settings
+#define BAT_MEASURE_ADC ADC1_GPIO34_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_6
+#define BAT_VOLTAGE_DIVIDER 2.605f           // voltage divider
+
+// Display Settings
+#define HAS_DISPLAY 2       // TFT-LCD
+#define TFT_TYPE DISPLAY_T_DISPLAY
+#define MY_DISPLAY_FLIP  1  // use if display is rotated
+#define MY_DISPLAY_WIDTH 135
+#define MY_DISPLAY_HEIGHT 240
+
+#endif

shared/hal/ttgotdisplays3.h

@@ -0,0 +1,24 @@
+// clang-format off
+// upload_speed 1500000
+// board esp32-s3-devkitc-1
+
+#ifndef _TTGOTDISPLAYS3_H
+#define _TTGOTDISPLAYS3_H
+
+#include <stdint.h>
+
+#define HAS_LED NOT_A_PIN
+#define HAS_BUTTON 14       // on board button (right side)
+
+// power management settings
+//#define BAT_MEASURE_ADC ADC1_GPIO4_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_6
+//#define BAT_VOLTAGE_DIVIDER 2.605f         // voltage divider
+
+// Display Settings
+#define HAS_DISPLAY 2       // TFT-LCD parallel
+#define TFT_TYPE DISPLAY_T_DISPLAY_S3
+#define MY_DISPLAY_FLIP  1  // use if display is rotated
+#define MY_DISPLAY_WIDTH 172
+#define MY_DISPLAY_HEIGHT 320
+
+#endif

shared/hal/ttgotdongledisplays3.h

@@ -0,0 +1,27 @@
+// clang-format off
+// upload_speed 1500000
+// board esp32-s3-devkitc-1
+
+// for pinouts see https://github.com/Xinyuan-LilyGO/T-Dongle-S3
+
+#ifndef _TTGOTDONGLEDISPLAYS3_H
+#define _TTGOTDONGLEDISPLAYS3_H
+
+#include <stdint.h>
+
+#define HAS_LED NOT_A_PIN
+#define RGB_LED_COUNT 1
+#define HAS_RGB_LED FastLED.addLeds<APA102, 40, 39, BGR>(leds, RGB_LED_COUNT)
+#define FASTLED_INTERNAL
+#define HAS_BUTTON 0       // dongle button is on GPIO0
+#define HAS_SDCARD  2      // dongle has a SD MMC card-reader/writer
+#define SDCARD_SLOTWIDTH 4 // dongle has 4 line interface
+#define SDCARD_SLOTCONFIG { .clk = GPIO_NUM_12, .cmd = GPIO_NUM_16, .d0 = GPIO_NUM_14, .d1 = GPIO_NUM_17, .d2 = GPIO_NUM_21, .d3 = GPIO_NUM_18, .cd = SDMMC_SLOT_NO_CD, .wp = SDMMC_SLOT_NO_WP, .width = 4, .flags = 0, }
+
+#define HAS_DISPLAY 3       // TFT-LCD
+#define TFT_TYPE DISPLAY_T_DONGLE_S3
+#define MY_DISPLAY_FLIP  1  // use if display is rotated
+#define MY_DISPLAY_WIDTH 80
+#define MY_DISPLAY_HEIGHT 160
+
+#endif

shared/hal/ttgotdongles3.h

@@ -0,0 +1,21 @@
+// clang-format off
+// upload_speed 1500000
+// board esp32-s3-devkitc-1
+
+// for pinouts see https://github.com/Xinyuan-LilyGO/T-Dongle-S3
+
+#ifndef _TTGOTDONGLES3_H
+#define _TTGOTDONGLES3_H
+
+#include <stdint.h>
+
+#define HAS_LED NOT_A_PIN
+#define RGB_LED_COUNT 1
+#define HAS_RGB_LED FastLED.addLeds<APA102, 40, 39, BGR>(leds, RGB_LED_COUNT)
+#define FASTLED_INTERNAL
+#define HAS_BUTTON 0       // dongle button is on GPIO0
+#define HAS_SDCARD  2      // dongle has a SD MMC card-reader/writer
+#define SDCARD_SLOTWIDTH 4 // dongle has 4 line interface
+#define SDCARD_SLOTCONFIG { .clk = GPIO_NUM_12, .cmd = GPIO_NUM_16, .d0 = GPIO_NUM_14, .d1 = GPIO_NUM_17, .d2 = GPIO_NUM_21, .d3 = GPIO_NUM_18, .cd = SDMMC_SLOT_NO_CD, .wp = SDMMC_SLOT_NO_WP, .width = 4, .flags = 0, }
+
+#endif

shared/hal/ttgotwristband.h

@@ -0,0 +1,35 @@
+// clang-format off
+// upload_speed 1500000
+// board pico32
+
+#ifndef _TTGOTWRISTBAND_H
+#define _TTGOTWRISTBAND_H
+
+#include <stdint.h>
+
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#define HAS_LED NOT_A_PIN  // no on board LED (?)
+#define HAS_BUTTON (33)    // on board button A
+
+// power management settings
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BAT_VOLTAGE_DIVIDER 2.605f           // voltage divider
+
+// Display Settings
+#define HAS_DISPLAY 2      // TFT-LCD
+#define MY_DISPLAY_FLIP  1 // use if display is rotated
+#define MY_DISPLAY_WIDTH 80
+#define MY_DISPLAY_HEIGHT 160
+#define TFT_MOSI GPIO_NUM_19 // SPI
+#define TFT_MISO NOT_A_PIN   // SPI
+#define TFT_SCLK GPIO_NUM_18 // SPI
+#define TFT_CS   GPIO_NUM_5  // Chip select control
+#define TFT_DC   GPIO_NUM_23 // Data Command control
+#define TFT_RST  GPIO_NUM_26 // Reset
+#define TFT_BL   GPIO_NUM_27 // LED back-light
+#define TFT_FREQUENCY 27000000
+#define TFT_TYPE LCD_ST7735S, FLAGS_NONE, TFT_FREQUENCY, TFT_CS, TFT_DC, TFT_RST, TFT_BL, TFT_MISO, TFT_MOSI, TFT_SCLK
+
+#endif
+

shared/hal/ttgov1.h

@@ -0,0 +1,42 @@
+// clang-format off
+// upload_speed 115200
+// board ttgo-lora32-v1
+
+#ifndef _TTGOV1_H
+#define _TTGOV1_H
+
+#include <stdint.h>
+
+// Hardware related definitions for TTGOv1 board
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1
+
+#define HAS_DISPLAY 1 // OLED-Display on board
+//#define MY_DISPLAY_FLIP  1 // uncomment this for rotated display
+#define HAS_LED LED_BUILTIN // set to NOT_A_PIN to disable
+#define LED_ACTIVE_LOW 1  // Onboard LED is active when pin is LOW
+#define HAS_BUTTON KEY_BUILTIN
+
+// enable only if you want to store a local paxcount table on the device
+// #define HAS_SDCARD  1      // this board has an SD-card-reader/writer
+// Pins for SD-card
+#define SDCARD_CS    (13)
+#define SDCARD_MOSI  (15)
+#define SDCARD_MISO  (2)
+#define SDCARD_SCLK  (14)
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA (4)
+#define MY_DISPLAY_SCL (15)
+#define MY_DISPLAY_RST (16)
+
+// This board reports back the wrong I2C address, so we overwrite it here
+#define MY_DISPLAY_ADDR 0x3C
+
+// Pins for LORA chip SPI interface come from board file, we need some
+// additional definitions for LMIC
+#define LORA_IO1  (33)
+#define LORA_IO2  (32)  // ref.:  https://www.thethingsnetwork.org/forum/t/big-esp32-sx127x-topic-part-3/18436
+
+#endif

shared/hal/ttgov2.h

@@ -0,0 +1,44 @@
+// clang-format off
+// upload_speed 921600
+// board ttgo-lora32-v2
+// https://github.com/LilyGO/TTGO-LORA32
+
+#ifndef _TTGOV2_H
+#define _TTGOV2_H
+
+#include <stdint.h>
+
+// Hardware related definitions for LilyGO TTGO LORA32 V2 Board
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+
+#define HAS_DISPLAY 1
+//#define MY_DISPLAY_FLIP  1 // uncomment this for rotated display
+#define HAS_LED NOT_A_PIN // on-board LED is wired to SCL (used by display) therefore totally useless
+
+// disable brownout detection (needed on TTGOv2 for battery powered operation)
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+// enable only if you want to store a local paxcount table on the device
+#define HAS_SDCARD  1      // this board has an SD-card-reader/writer
+// Pins for SD-card
+#define SDCARD_CS    (13)
+#define SDCARD_MOSI  (15)
+#define SDCARD_MISO  (2)
+#define SDCARD_SCLK  (14)
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA (21)
+#define MY_DISPLAY_SCL (22)
+#define MY_DISPLAY_RST NOT_A_PIN
+
+// Pins for LORA chip SPI interface come from board file, we need some
+// additional definitions for LMIC
+// ********************************************************************************************
+//! LORA_IO1 is not connected on LilyGO TTGO V2 - bodge wire from LORA_IO1 to GPIO33 necessary
+#define LORA_IO1  (33)
+// ********************************************************************************************
+#define LORA_IO2  LMIC_UNUSED_PIN
+
+#endif

shared/hal/ttgov21new.h

@@ -0,0 +1,44 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+#ifndef _TTGOV21NEW_H
+#define _TTGOV21NEW_H
+
+#include <stdint.h>
+
+/*  Hardware related definitions for TTGO V2.1 Board
+// ATTENTION: check your board version!
+// This settings are for boards labeled v1.6 or v1.6.1 on pcb, NOT for v1.5 or older
+*/
+
+#define HAS_LORA         1 // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+
+// enable only if you want to store a local paxcount table on the device
+#define HAS_SDCARD  2      // this board has a SD MMC card-reader/writer
+#define SDCARD_SLOTWIDTH 4 // 4-line interface
+
+#define HAS_DISPLAY 1
+#define HAS_LED (25) // green on board LED
+//#define HAS_LED NOT_A_PIN
+
+#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA (21)
+#define MY_DISPLAY_SCL (22)
+#define MY_DISPLAY_RST NOT_A_PIN
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (18)
+#define LORA_MISO (19)
+#define LORA_MOSI (27)
+#define LORA_RST  (23)
+#define LORA_IRQ  (26)
+#define LORA_IO1  (33)
+#define LORA_IO2  (32)
+
+#endif

shared/hal/ttgov21old.h

@@ -0,0 +1,51 @@
+// clang-format off
+// upload_speed 921600
+// board esp32dev
+
+#ifndef _TTGOV21OLD_H
+#define _TTGOV21OLD_H
+
+#include <stdint.h>
+
+
+/*  Hardware related definitions for TTGO V2.1 Board
+// ATTENTION: check your board version!
+// This settings are for boards without label on pcb, or labeled v1.5 on pcb
+// see https://github.com/manuelbl/ttn-esp32/wiki/Boards-and-Pins
+*/
+
+#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+#define HAS_LED NOT_A_PIN // no usable LED on board
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+// enable only if you want to store a local paxcount table on the device
+#define HAS_SDCARD  1      // this board has an SD-card-reader/writer
+// Pins for SD-card
+#define SDCARD_CS    (13)
+#define SDCARD_MOSI  (15)
+#define SDCARD_MISO  (2)
+#define SDCARD_SCLK  (14)
+
+#define HAS_DISPLAY 1
+#define MY_DISPLAY_FLIP  1 // rotated display
+//#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+//#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
+
+// Pins for I2C interface of OLED Display
+#define MY_DISPLAY_SDA (21)
+#define MY_DISPLAY_SCL (22)
+#define MY_DISPLAY_RST NOT_A_PIN
+
+// Pins for LORA chip SPI interface, reset line and interrupt lines
+#define LORA_SCK  (5) 
+#define LORA_CS   (18)
+#define LORA_MISO (19)
+#define LORA_MOSI (27)
+#define LORA_RST  LMIC_UNUSED_PIN
+// #define LORA_RST  (12)  // v1.5 labelled with pcb date 20180523
+#define LORA_IRQ  (26)
+#define LORA_IO1  (33)
+#define LORA_IO2  (32)
+
+#endif

shared/hal/wemos32matrix.h

@@ -0,0 +1,47 @@
+// clang-format off
+// upload_speed 921600
+// board lolin32
+
+#ifndef _WEMOS32MATRIX_H
+#define _WEMOS32MATRIX_H
+
+#include <stdint.h>
+
+#define HAS_LED NOT_A_PIN // no LED
+
+// LED Matrix display settings
+#define HAS_MATRIX_DISPLAY              1       // Uncomment to enable LED matrix display output
+#define LED_MATRIX_WIDTH                (32*2)  // Width (cols) in pixels (LEDs) of your display, must be 32X
+#define LED_MATRIX_HEIGHT               (16*1)  // Height (rows) in pixels (LEDs) of your display, must be 16X
+
+// Pin numbers work fine for Wemos Lolin32 board (all used pins are on 1 side of the board)
+// Explanation of pin signals see https://learn.adafruit.com/32x16-32x32-rgb-led-matrix/new-wiring
+#define MATRIX_DISPLAY_SCAN_US          500     // Matrix display scan rate in microseconds (1ms is about 'acceptable')
+#define LED_MATRIX_LATCHPIN             13      // LAT (or STB = Strobe)
+#define LED_MATRIX_CLOCKPIN             32      // CLK
+#define LED_MATRIX_EN_74138             12      // EN (or OE)
+#define LED_MATRIX_LA_74138             14      // LA (or A)
+#define LED_MATRIX_LB_74138             27      // LB (or B)
+#define LED_MATRIX_LC_74138             25      // LC (or C)
+#define LED_MATRIX_LD_74138             26      // LD (or D)
+#define LED_MATRIX_DATA_R1              33      // R1 (or R0)
+
+// CLK: The clock signal moves the data bits from pin R1 ("red") in the shift registers
+// LAT: The latch signal enables LEDs according to the shift register's contents
+// Line Selects: LA, LB, LC, LD select which rows of the display are currently lit (0 .. 15)
+// OE: Output enable switches the LEDs on/off while transitioning from one row to the next
+
+/*
+How it works:
+
+1. clock out 8 bytes for columns via R1 and CLK (8 * 8 bit -> 64 columns)
+2. OE disable (LEDs off)
+3. select line to lit with LA/LB/LC/LD hex coded (4 bit -> 16 rows)
+4. latch data from shift registers to columns
+5. OE enable (LEDs on)
+6. repeat with step1 for next line
+*/
+
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#endif

shared/hal/wemos32oled.h

@@ -0,0 +1,20 @@
+// clang-format off
+// upload_speed 921600
+// board lolin32
+
+#ifndef _WEMOS32OLED_H
+#define _WEMOS32OLED_H
+
+#include <stdint.h>
+
+#define HAS_LED NOT_A_PIN // no LED
+
+#define HAS_DISPLAY 1
+#define MY_DISPLAY_SDA (5)
+#define MY_DISPLAY_SCL (4)
+#define MY_DISPLAY_RST NOT_A_PIN
+#define MY_DISPLAY_FLIP  1 // use if display is rotated
+
+#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#endif