diff --git a/platformio.ini b/platformio.ini
index 9f841819..a4499620 100644
--- a/platformio.ini
+++ b/platformio.ini
@@ -7,7 +7,7 @@
 
 ; ---> SELECT THE TARGET PLATFORM HERE! <---
 [board]
-;halfile = generic.h
+halfile = generic.h
 ;halfile = ebox.h
 ;halfile = eboxtube.h
 ;halfile = ecopower.h
@@ -18,7 +18,7 @@
 ;halfile = ttgov21old.h
 ;halfile = ttgov21new.h
 ;halfile = ttgofox.h
-halfile = ttgobeam.h
+;halfile = ttgobeam.h
 ;halfile = fipy.h
 ;halfile = lopy.h
 ;halfile = lopy4.h
@@ -81,7 +81,7 @@ lib_deps_all =
 build_flags_basic =
     -include "src/hal/${board.halfile}"
     -include "src/paxcounter.conf"
-    ;-w
+    -w
     '-DCORE_DEBUG_LEVEL=${common.debug_level}'
     '-DLOG_LOCAL_LEVEL=${common.debug_level}'
     '-DPROGVERSION="${common.release_version}"'
diff --git a/src/hal/ttgobeam.h b/src/hal/ttgobeam.h
index a7851877..41fd0ef0 100644
--- a/src/hal/ttgobeam.h
+++ b/src/hal/ttgobeam.h
@@ -25,13 +25,13 @@
 // GPS settings
 #define HAS_GPS 1 // use on board GPS
 #define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M
-#define GPS_INT GPIO_NUM_34 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO34
+//#define GPS_INT GPIO_NUM_34 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO34
 
 // enable only if device has these sensors, otherwise comment these lines
 // BME680 sensor on I2C bus
-#define HAS_BME 1 // Enable BME sensors in general
-#define HAS_BME680 SDA, SCL
-#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
+//#define HAS_BME 1 // Enable BME sensors in general
+//#define HAS_BME680 SDA, SCL
+//#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
 
 // display (if connected)
 #define HAS_DISPLAY U8X8_SSD1306_128X64_NONAME_HW_I2C
diff --git a/src/paxcounter.conf b/src/paxcounter.conf
index 1da72086..13b6c0b7 100644
--- a/src/paxcounter.conf
+++ b/src/paxcounter.conf
@@ -71,7 +71,7 @@
 #define TIME_SYNC_INTERVAL_RETRY        10      // retry time sync after lost sync each .. minutes [default = 10], 0 means off
 #define TIME_SYNC_COMPILEDATE           0       // set to 1 to use compile date to initialize RTC after power outage [default = 0]
 #define TIME_SYNC_LORAWAN               0       // set to 1 to use LORA network as time source, 0 means off [default = 0]
-#define TIME_SYNC_LORASERVER            1       // set to 1 to use LORA timeserver as time source, 0 means off [default = 0]
+#define TIME_SYNC_LORASERVER            0       // set to 1 to use LORA timeserver as time source, 0 means off [default = 0]
 
 // settings for syncing time with timeserver applications
 #define TIME_SYNC_SAMPLES               1       // number of time requests for averaging