diff --git a/platformio.ini b/platformio.ini
index 511be877..91466e24 100644
--- a/platformio.ini
+++ b/platformio.ini
@@ -24,6 +24,7 @@ env_default = generic
 ;env_default = lolin32litelora
 ;env_default = lolin32lora
 ;env_default = lolin32lite
+;env_default = wemos32oled
 ;env_default = octopus32
 ;env_default = ecopower, eboxtube, heltec, ttgobeam, lopy4, lopy, ttgov21old, ttgov21new, ttgofox
 ;
@@ -360,6 +361,21 @@ upload_protocol = ${common.upload_protocol}
 extra_scripts = ${common.extra_scripts}
 monitor_speed = ${common.monitor_speed}
 
+[env:wemos32oled]
+platform = ${common.platform_espressif32}
+framework = arduino
+board = lolin32
+board_build.partitions = ${common.board_build.partitions}
+upload_speed = 921600
+lib_deps =
+    ${common.lib_deps_basic}
+    ${common.lib_deps_display}
+build_flags =
+    ${common.build_flags_all}
+upload_protocol = ${common.upload_protocol}
+extra_scripts = ${common.extra_scripts}
+monitor_speed = ${common.monitor_speed}
+
 [env:octopus32]
 platform = ${common.platform_espressif32}
 framework = arduino
diff --git a/src/hal/wemos32oled.h b/src/hal/wemos32oled.h
new file mode 100644
index 00000000..d5c27832
--- /dev/null
+++ b/src/hal/wemos32oled.h
@@ -0,0 +1,45 @@
+// clang-format off
+
+#ifndef _WEMOS32OLED_H
+#define _WEMOS32OLED_H
+
+#include <stdint.h>
+
+// Hardware related definitions for TTGO T-Beam board
+// (only) for older T-Beam version T22_V05 eternal wiring LORA_IO1 to GPIO33 is needed!
+//
+// pinouts taken from http://tinymicros.com/wiki/TTGO_T-Beam
+
+#define HAS_LED NOT_A_PIN // no LED
+
+//#define HAS_LORA 1       // comment out if device shall not send data via LoRa
+//#define CFG_sx1276_radio 1 // HPD13A LoRa SoC
+//#define BOARD_HAS_PSRAM // use extra 4MB external RAM
+//#define HAS_BUTTON GPIO_NUM_39 // on board button (next to reset)
+//#define BAT_MEASURE_ADC ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
+//#define BAT_VOLTAGE_DIVIDER 2 // voltage divider 100k/100k on board
+
+// GPS settings
+//#define HAS_GPS 1 // use on board GPS
+//#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_12, GPIO_NUM_15 // UBlox NEO 6M
+//#define GPS_INT GPIO_NUM_34 // 30ns accurary timepulse, to be external wired on pcb: NEO 6M Pin#3 -> GPIO34
+
+// enable only if device has these sensors, otherwise comment these lines
+// BME680 sensor on I2C bus
+//#define HAS_BME 1 // Enable BME sensors in general
+//#define HAS_BME680 SDA, SCL
+//#define BME680_ADDR BME680_I2C_ADDR_PRIMARY // !! connect SDIO of BME680 to GND !!
+
+// display (if connected)
+#define HAS_DISPLAY U8X8_SSD1306_128X64_NONAME_HW_I2C
+#define MY_OLED_SDA (5)
+#define MY_OLED_SCL (4)
+#define MY_OLED_RST U8X8_PIN_NONE
+#define DISPLAY_FLIP  1 // use if display is rotated
+
+// user defined sensors (if connected)
+//#define HAS_SENSORS 1 // comment out if device has user defined sensors
+
+//#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature
+
+#endif