Merge pull request #427 from cyberman54/development

Development

include/i2cscan.h

@@ -2,11 +2,15 @@
 #define _I2CSCAN_H
 
 #include <Arduino.h>
-#ifdef HAS_PMU
+
-#include "axp20x.h"
+#define SSD1306_PRIMARY_ADDRESS (0x3D)
-#endif
+#define SSD1306_SECONDARY_ADDRESS (0x3C)
+#define BME_PRIMARY_ADDRESS (0x77)
+#define BME_SECONDARY_ADDRESS (0x76)
+#define AXP192_PRIMARY_ADDRESS (0x34)
+#define MCP_24AA02E64_PRIMARY_ADDRESS (0x50)
+#define QUECTEL_GPS_PRIMARY_ADDRESS (0x10)
 
 int i2c_scan(void);
-void AXP192_init(void);
 
 #endif

include/lorawan.h

@@ -47,7 +47,8 @@ void lora_queuereset(void);
 void myRxCallback(void *pUserData, uint8_t port, const uint8_t *pMsg,
                   size_t nMsg);
 void myTxCallback(void *pUserData, int fSuccess);
-void mac_decode(const uint8_t cmd[], const uint8_t cmdlength);
+void mac_decode(const uint8_t cmd[], const uint8_t cmdlen, const mac_t table[],
+                const uint8_t tablesize);
 
 #if (TIME_SYNC_LORAWAN)
 void user_request_network_time_callback(void *pVoidUserUTCTime,

include/main.h

@@ -7,6 +7,7 @@
 #include <esp_coexist.h>     // needed for showing coex sw version
 
 #include "globals.h"
+#include "power.h"
 #include "i2cscan.h"
 #include "blescan.h"
 #include "wifiscan.h"

include/power.h

@@ -0,0 +1,13 @@
+#ifndef _POWER_H
+#define _POWER_H
+
+#include <Arduino.h>
+#include "i2cscan.h"
+
+#ifdef HAS_PMU
+#include <axp20x.h>
+#endif
+
+void AXP192_init(void);
+
+#endif

src/i2cscan.cpp

@@ -5,14 +5,6 @@
 // Local logging tag
 static const char TAG[] = __FILE__;
 
-#define SSD1306_PRIMARY_ADDRESS (0x3D)
-#define SSD1306_SECONDARY_ADDRESS (0x3C)
-#define BME_PRIMARY_ADDRESS (0x77)
-#define BME_SECONDARY_ADDRESS (0x76)
-#define AXP192_PRIMARY_ADDRESS (0x34)
-#define MCP_24AA02E64_PRIMARY_ADDRESS (0x50)
-#define QUECTEL_GPS_PRIMARY_ADDRESS (0x10)
-
 int i2c_scan(void) {
 
   int i2c_ret, addr;
@@ -23,7 +15,11 @@ int i2c_scan(void) {
   for (addr = 8; addr <= 119; addr++) {
 
 // scan i2c bus with no more to 100KHz
+#ifdef HAS_DISPLAY
+    Wire.begin(MY_OLED_SDA, MY_OLED_SCL, 100000);
+#else
     Wire.begin(SDA, SCL, 100000);
+#endif
     Wire.beginTransmission(addr);
     Wire.write(addr);
     i2c_ret = Wire.endTransmission();
@@ -45,9 +41,6 @@ int i2c_scan(void) {
 
       case AXP192_PRIMARY_ADDRESS:
         ESP_LOGI(TAG, "0x%X: AXP192 power management", addr);
-#ifdef HAS_PMU
-        AXP192_init();
-#endif
         break;
 
       case QUECTEL_GPS_PRIMARY_ADDRESS:
@@ -69,42 +62,3 @@ int i2c_scan(void) {
 
   return devices;
 }
-
-#ifdef HAS_PMU
-
-void AXP192_init(void) {
-
-  AXP20X_Class axp;
-
-  if (axp.begin(Wire, AXP192_PRIMARY_ADDRESS))
-    ESP_LOGI(TAG, "AXP192 PMU initialization failed");
-  else {
-
-    axp.setPowerOutPut(AXP192_LDO2, AXP202_ON);
-    axp.setPowerOutPut(AXP192_LDO3, AXP202_ON);
-    axp.setPowerOutPut(AXP192_DCDC2, AXP202_ON);
-    axp.setPowerOutPut(AXP192_EXTEN, AXP202_ON);
-    axp.setPowerOutPut(AXP192_DCDC1, AXP202_ON);
-    axp.setDCDC1Voltage(3300);
-    axp.setChgLEDMode(AXP20X_LED_BLINK_1HZ);
-    //axp.setChgLEDMode(AXP20X_LED_OFF);
-    axp.adc1Enable(AXP202_BATT_CUR_ADC1, 1);
-
-#ifdef PMU_INT
-    pinMode(PMU_INT, INPUT_PULLUP);
-    attachInterrupt(digitalPinToInterrupt(PMU_INT),
-                    [] {
-                      ESP_LOGI(TAG, "Power source changed");
-                      /* put your code here */
-                    },
-                    FALLING);
-    axp.enableIRQ(AXP202_VBUS_REMOVED_IRQ | AXP202_VBUS_CONNECT_IRQ |
-                      AXP202_BATT_REMOVED_IRQ | AXP202_BATT_CONNECT_IRQ,
-                  1);
-    axp.clearIRQ();
-#endif // PMU_INT
-
-    ESP_LOGI(TAG, "AXP192 PMU initialized.");
-  }
-}
-#endif // HAS_PMU

src/lmic_config.h

@@ -2,19 +2,16 @@
 
 // COUNTRY SETTINGS
 // --> please check with you local regulations for ISM band frequency use!
-//
-// CFG_eu868	EU 863-870 MHz
-// CFG_us915    US 902-928 MHz
-// CFG_au921	Australia 915-928 MHz
-// CFG_as923	Asia 923 MHz
-// CFG_in866	India 865-867 MHz
 
-#define CFG_eu868 1
+#define CFG_eu868 1 // Europe (high band)
-//#define CFG_us915 1
+//#define CFG_eu433 1 // Europe (low band)
-//#define CFG_in866 1
+//#define CFG_us915 1 // USA, Canada and South America
-//#define CFG_au921 1
+//#define CFG_in866 1 // India
-//#define CFG_as923 1
+//#define CFG_au921 1 // Australia
-//#define LMIC_COUNTRY_CODE LMIC_COUNTRY_CODE_JP	/* for as923-JP */
+//#define CFG_as923 1 // Asia
+//#define CFG_cn783 1 // China (high band)
+//#define CFG_cn490 1 // China (low band)
+//#define CFG_kr920 1 // Korea
 
 // LMIC LORAWAN STACK SETTINGS
 // --> adapt to your device only if necessary
@@ -26,18 +23,12 @@
 // time sync via LoRaWAN network, note: not supported by TTNv2
 // #define LMIC_ENABLE_DeviceTimeReq 1
 
-// 16 μs per tick
-// LMIC requires ticks to be 15.5μs - 100 μs long
-#define US_PER_OSTICK_EXPONENT 4
-#define US_PER_OSTICK (1 << US_PER_OSTICK_EXPONENT)
-#define OSTICKS_PER_SEC (1000000 / US_PER_OSTICK)
-
 // This tells LMIC to make the receive windows bigger, in case your clock is
 // faster or slower. This causes the transceiver to be earlier switched on,
 // so consuming more power. You may sharpen (reduce) this value if you are
 // limited on battery.
 // ATTN: VALUES > 7 WILL CAUSE RECEPTION AND JOIN PROBLEMS WITH HIGH SF RATES
-#define CLOCK_ERROR_PROCENTAGE 7
+//#define CLOCK_ERROR_PROCENTAGE 7
 
 // Set this to 1 to enable some basic debug output (using printf) about
 // RF settings used during transmission and reception. Set to 2 to
@@ -51,6 +42,11 @@
 // current implementation only works on AVR, though.
 //#define LMIC_PRINTF_TO Serial
 
+// Change the SPI clock speed if you encounter errors
+// communicating with the radio.
+// The standard range is 125kHz-8MHz, but some boards can go faster.
+//#define LMIC_SPI_FREQ 1E6
+
 // Any runtime assertion failures are printed to this serial port (or
 // any other Print object). If this is unset, any failures just silently
 // halt execution.
@@ -92,7 +88,7 @@
 // implementation is optimized for speed on 32-bit processors using
 // fairly big lookup tables, but it takes up big amounts of flash on the
 // AVR architecture.
-//#define USE_ORIGINAL_AES
+#define USE_ORIGINAL_AES
 //
 // This selects the AES implementation written by Ideetroon for their
 // own LoRaWAN library. It also uses lookup tables, but smaller
@@ -100,4 +96,4 @@
 // also about twice as slow as the original).
 // #define USE_IDEETRON_AES
 //
-#define USE_MBEDTLS_AES
+//#define USE_MBEDTLS_AES

src/lorawan.cpp

@@ -24,8 +24,7 @@ TaskHandle_t lmicTask = NULL, lorasendTask = NULL;
 // table of LORAWAN MAC messages sent by the network to the device
 // format: opcode, cmdname (max 19 chars), #bytes params
 // source: LoRaWAN 1.1 Specification (October 11, 2017)
-
+static const mac_t MACdn_table[] = {
-static mac_t table[] = {
     {0x01, "ResetConf", 1},          {0x02, "LinkCheckAns", 2},
     {0x03, "LinkADRReq", 4},         {0x04, "DutyCycleReq", 1},
     {0x05, "RXParamSetupReq", 4},    {0x06, "DevStatusReq", 0},
@@ -35,8 +34,15 @@ static mac_t table[] = {
     {0x0D, "DeviceTimeAns", 5},      {0x0E, "ForceRejoinReq", 2},
     {0x0F, "RejoinParamSetupReq", 1}};
 
-static const uint8_t cmdtablesize =
+// table of LORAWAN MAC messages sent by the device to the network
-    sizeof(table) / sizeof(table[0]); // number of commands in MAC table
+static const mac_t MACup_table[] = {
+    {0x01, "ResetInd", 1},        {0x02, "LinkCheckReq", 0},
+    {0x03, "LinkADRAns", 1},      {0x04, "DutyCycleAns", 0},
+    {0x05, "RXParamSetupAns", 1}, {0x06, "DevStatusAns", 2},
+    {0x07, "NewChannelAns", 1},   {0x08, "RxTimingSetupAns", 0},
+    {0x09, "TxParamSetupAns", 0}, {0x0A, "DlChannelAns", 1},
+    {0x0B, "RekeyInd", 1},        {0x0C, "ADRParamSetupAns", 0},
+    {0x0D, "DeviceTimeReq", 0},   {0x0F, "RejoinParamSetupAns", 1}};
 
 class MyHalConfig_t : public Arduino_LMIC::HalConfiguration_t {
 
@@ -539,7 +545,9 @@ void lmictask(void *pvParameters) {
 // faster or slower. This causes the transceiver to be earlier switched on,
 // so consuming more power. You may sharpen (reduce) CLOCK_ERROR_PERCENTAGE
 // in src/lmic_config.h if you are limited on battery.
+#ifdef CLOCK_ERROR_PROCENTAGE
   LMIC_setClockError(MAX_CLOCK_ERROR * CLOCK_ERROR_PROCENTAGE / 100);
+#endif
   // Set the data rate to Spreading Factor 7.  This is the fastest supported
   // rate for 125 kHz channels, and it minimizes air time and battery power.
   // Set the transmission power to 14 dBi (25 mW).
@@ -568,26 +576,26 @@ void myRxCallback(void *pUserData, uint8_t port, const uint8_t *pMsg,
 
   // display type of received data
   if (nMsg)
-    ESP_LOGI(TAG, "Received %u bytes of payload on port %u", nMsg, port);
+    ESP_LOGI(TAG, "Received %u byte(s) of payload on port %u", nMsg, port);
   else if (port)
     ESP_LOGI(TAG, "Received empty message on port %u", port);
 
   // list MAC messages, if any
-  /*
   uint8_t nMac = pMsg - &LMIC.frame[0];
   if (port != MACPORT)
     --nMac;
   if (nMac) {
-    ESP_LOGI(TAG, "Received %u byte MAC message", nMac);
+    ESP_LOGI(TAG, "%u byte(s) downlink MAC commands", nMac);
     // NOT WORKING YET
-    // whe need to strip some protocol overhead from LMIC.frame to unwrap the
+    // whe need to unwrap the MAC command from LMIC.frame here
-    // MAC command
+    // mac_decode(LMIC.frame, nMac, MACdn_table, sizeof(MACdn_table) /
-    mac_decode(LMIC.frame, nMac);
+    // sizeof(MACdn_table[0]));
-    */
+  }
 
   if (LMIC.pendMacLen) {
-    ESP_LOGI(TAG, "Received %u byte MAC message", LMIC.pendMacLen);
+    ESP_LOGI(TAG, "%u byte(s) uplink MAC commands", LMIC.pendMacLen);
-    mac_decode(LMIC.pendMacData, LMIC.pendMacLen);
+    mac_decode(LMIC.pendMacData, LMIC.pendMacLen, MACup_table,
+               sizeof(MACup_table) / sizeof(MACup_table[0]));
   }
 
   switch (port) {
@@ -623,32 +631,34 @@ void myTxCallback(void *pUserData, int fSuccess) {
 }
 
 // decode LORAWAN MAC message
-void mac_decode(const uint8_t cmd[], const uint8_t cmdlength) {
+void mac_decode(const uint8_t cmd[], const uint8_t cmdlen, const mac_t table[],
+                const uint8_t tablesize) {
 
-  if (!cmdlength)
+  if (!cmdlen)
     return;
 
-  uint8_t foundcmd[cmdlength], cursor = 0;
+  uint8_t foundcmd[cmdlen], cursor = 0;
 
-  while (cursor < cmdlength) {
+  while (cursor < cmdlen) {
+
+    int i = tablesize; // number of commands in table
 
-    int i = cmdtablesize;
     while (i--) {
       if (cmd[cursor] == table[i].opcode) { // lookup command in opcode table
         cursor++;                           // strip 1 byte opcode
-        if ((cursor + table[i].params) <= cmdlength) {
+        if ((cursor + table[i].params) <= cmdlen) {
           memmove(foundcmd, cmd + cursor,
                   table[i].params); // strip opcode from cmd array
           cursor += table[i].params;
-          ESP_LOGD(TAG, "Network command %s", table[i].cmdname);
+          ESP_LOGD(TAG, "MAC command %s", table[i].cmdname);
         } else
-          ESP_LOGD(TAG, "MAC message 0x%02X with missing parameter(s)",
+          ESP_LOGD(TAG, "MAC command 0x%02X with missing parameter(s)",
                    table[i].opcode);
         break;   // command found -> exit table lookup loop
       }          // end of command validation
     }            // end of command table lookup loop
     if (i < 0) { // command not found -> skip it
-      ESP_LOGD(TAG, "Unknown MAC message 0x%02X", cmd[cursor]);
+      ESP_LOGD(TAG, "Unknown MAC command 0x%02X", cmd[cursor]);
       cursor++;
     }
   } // command parsing loop

src/main.cpp

@@ -169,6 +169,17 @@ void setup() {
   ESP_LOGI(TAG, "TinyGPS+ version %s", TinyGPSPlus::libraryVersion());
 #endif
 
+// setup power on boards with power management logic
+#ifdef EXT_POWER_SW
+  pinMode(EXT_POWER_SW, OUTPUT);
+  digitalWrite(EXT_POWER_SW, EXT_POWER_ON);
+  strcat_P(features, " VEXT");
+#endif
+#ifdef HAS_PMU
+  AXP192_init();
+  strcat_P(features, " PMU");
+#endif
+
   i2c_scan();
 
 #endif // verbose
@@ -189,13 +200,6 @@ void setup() {
   strcat_P(features, " PSRAM");
 #endif
 
-// set external power mode
-#ifdef EXT_POWER_SW
-  pinMode(EXT_POWER_SW, OUTPUT);
-  digitalWrite(EXT_POWER_SW, EXT_POWER_ON);
-  strcat_P(features, " VEXT");
-#endif
-
 #ifdef BAT_MEASURE_EN
   pinMode(BAT_MEASURE_EN, OUTPUT);
 #endif

src/power.cpp

@@ -0,0 +1,42 @@
+// Basic config
+#include "globals.h"
+#include "power.h"
+
+#ifdef HAS_PMU
+
+void AXP192_init(void) {
+
+  AXP20X_Class axp;
+
+  if (axp.begin(Wire, AXP192_PRIMARY_ADDRESS))
+    ESP_LOGI(TAG, "AXP192 PMU initialization failed");
+  else {
+
+    axp.setPowerOutPut(AXP192_LDO2, AXP202_ON);
+    axp.setPowerOutPut(AXP192_LDO3, AXP202_ON);
+    axp.setPowerOutPut(AXP192_DCDC2, AXP202_ON);
+    axp.setPowerOutPut(AXP192_EXTEN, AXP202_ON);
+    axp.setPowerOutPut(AXP192_DCDC1, AXP202_ON);
+    axp.setDCDC1Voltage(3300);
+    axp.setChgLEDMode(AXP20X_LED_BLINK_1HZ);
+    // axp.setChgLEDMode(AXP20X_LED_OFF);
+    axp.adc1Enable(AXP202_BATT_CUR_ADC1, 1);
+
+#ifdef PMU_INT
+    pinMode(PMU_INT, INPUT_PULLUP);
+    attachInterrupt(digitalPinToInterrupt(PMU_INT),
+                    [] {
+                      ESP_LOGI(TAG, "Power source changed");
+                      /* put your code here */
+                    },
+                    FALLING);
+    axp.enableIRQ(AXP202_VBUS_REMOVED_IRQ | AXP202_VBUS_CONNECT_IRQ |
+                      AXP202_BATT_REMOVED_IRQ | AXP202_BATT_CONNECT_IRQ,
+                  1);
+    axp.clearIRQ();
+#endif // PMU_INT
+
+    ESP_LOGI(TAG, "AXP192 PMU initialized.");
+  }
+}
+#endif // HAS_PMU

src/wifiscan.cpp

@@ -71,6 +71,7 @@ void wifi_sniffer_init(void) {
   ESP_ERROR_CHECK(
       esp_wifi_set_storage(WIFI_STORAGE_RAM)); // we don't need NVRAM
   ESP_ERROR_CHECK(esp_wifi_set_mode(WIFI_MODE_NULL));
+  ESP_ERROR_CHECK(esp_wifi_set_ps(WIFI_PS_NONE)); // no modem power saving
   ESP_ERROR_CHECK(esp_wifi_start()); // channel switch throws error without
   ESP_ERROR_CHECK(esp_wifi_set_promiscuous_filter(&filter)); // set frame filter
   ESP_ERROR_CHECK(esp_wifi_set_promiscuous_rx_cb(&wifi_sniffer_packet_handler));