ESP32-PaxCounter/src/hal/generic.h

// clang-format off

#ifndef _GENERIC_H
#define _GENERIC_H

#include <stdint.h>

// Hardware related definitions for generic ESP32 boards
// generic.h is kitchensink with all available options

#define HAS_LORA 1 // comment out if device shall not send data via LoRa or has no LoRa
#define HAS_SPI 1  // comment out if device shall not send data via SPI
// pin definitions for SPI slave interface
#define SPI_MOSI GPIO_NUM_23
#define SPI_MISO GPIO_NUM_19
#define SPI_SCLK GPIO_NUM_18
#define SPI_CS   GPIO_NUM_5

// enable only if device has these sensors, otherwise comment these lines
// BME680 sensor on I2C bus
#define HAS_BME GPIO_NUM_21, GPIO_NUM_22 // SDA, SCL
#define BME_ADDR BME680_I2C_ADDR_PRIMARY // connect SDIO of BME680 to GND

// user defined sensors
//#define HAS_SENSORS 1 // comment out if device has user defined sensors

#define CFG_sx1276_radio 1 // select LoRa chip
//#define CFG_sx1272_radio 1 // select LoRa chip
#define BOARD_HAS_PSRAM // use if board has external PSRAM
#define DISABLE_BROWNOUT 1 // comment out if you want to keep brownout feature

#define HAS_DISPLAY U8X8_SSD1306_128X64_NONAME_HW_I2C
//#define DISPLAY_FLIP  1 // use if display is rotated
#define HAS_BATTERY_PROBE ADC1_GPIO35_CHANNEL // battery probe GPIO pin -> ADC1_CHANNEL_7
#define BATT_FACTOR 2 // voltage divider 100k/100k on board

#define HAS_LED (21) // on board  LED
#define HAS_BUTTON (39) // on board button
#define HAS_RGB_LED (0) // WS2812B RGB LED on GPIO0

#define BOARD_HAS_PSRAM // use extra 4MB extern RAM

#define HAS_GPS 1 // use if board has GPS
#define GPS_SERIAL 9600, SERIAL_8N1, GPIO_NUM_17, GPIO_NUM_16 // UBlox NEO 6M or 7M with default configuration

// Pins for I2C interface of OLED Display
#define MY_OLED_SDA (4)
#define MY_OLED_SCL (15)
#define MY_OLED_RST (16)

// Pins for on board DS3231 RTC chip
#define HAS_RTC MY_OLED_SDA, MY_OLED_SCL // SDA, SCL
#define RTC_INT GPIO_NUM_34 // interrupt input from rtc
#define RTC_CLK (1000) // frequency of RTC clock signal in ms

// Settings for IF482 interface
#define HAS_IF482 9600, SERIAL_7E1, GPIO_NUM_12, GPIO_NUM_14 // IF482 serial port parameters

// Settings for DCF77 interface
#define HAS_DCF77 GPIO_NUM_1
//#define DCF77_ACTIVE_LOW 1

// Pins for LORA chip SPI interface, reset line and interrupt lines
#define LORA_SCK  (5) 
#define LORA_CS   (18)
#define LORA_MISO (19)
#define LORA_MOSI (27)
#define LORA_RST  (14)
#define LORA_IRQ  (26)
#define LORA_IO1  (33)
#define LORA_IO2  LMIC_UNUSED_PIN

// I2C config for Microchip 24AA02E64 DEVEUI unique address
#define MCP_24AA02E64_I2C_ADDRESS 0x50 // I2C address for the 24AA02E64 
#define MCP_24AA02E64_MAC_ADDRESS 0xF8 // Memory adress of unique deveui 64 bits

#endif